In this paper, we put forward a proof of concept for sixth generation (6G) Terabit infrared (IR) laser-based indoor optical wireless networks. We propose a novel double-tier access point (AP) architecture based on anarray of arraysof vertical cavity surface emitting lasers (VCSELs) to provide a seamless grid-of-beam (GoB) coverage with multi-Gb/s per beam. We present systematic design and thorough analytical modeling of the AP architecture, which are then applied to downlink system modeling using non-imaging angle diversity receivers (ADRs). We propose static beam clustering with coordinated multi-beam joint transmission (CoMB-JT) for network interference management and devise various clustering strategies to address inter-beam interference (IBI) and inter-cluster interference (ICI). Non-orthogonal multiple access (NOMA) and orthogonal frequency division multiple access (OFDMA) schemes are also adopted to handle intra-cluster interference, and the resulting signal-to-interference-plus-noise ratio (SINR) and achievable data rate are derived. The network performance is studied in terms of spatial distributions and statistics of the downlink SINR and data rate through extensive computer simulations. The results demonstrate that data rates up to 15 Gb/s are achieved within the coverage area and a properly devised clustering strikes a balance between the sum rate and fairness depending on the number of users.

Optical wireless communication (OWC) has recently received massive interest as a new technology that can support the enormous data traffic increasing on daily basis. In particular, laser-based OWC networks can provide terabits per second (Tbps) aggregate data rates. However, the emerging OWC networks require a high number of optical access points (APs), each AP corresponding to an optical cell, to provide uniform coverage for multiple users. Therefore, inter-cell interference (ICI) and multi-user interference (MUI) are crucial issues that must be managed efficiently to provide high spectral efficiency. In radio frequency (RF) networks, rate splitting (RS) is proposed as a transmission scheme to serve multiple users simultaneously following a certain strategy. It was shown that RS provides high data rates compared to orthogonal and non-orthogonal interference management schemes. Considering the high density of OWC networks, the application of RS within each optical cell might not be practical due to severe ICI. In this paper, a novel strategy is derived, referred to as blind interference alignment-rate splitting (BIA-RS), to fully coordinate the transmission among the optical APs, while determining the precoding matrices of multiple groups of users formed beforehand. Therefore, RS can be implemented within each group to manage MUI. The proposed BIA-RS scheme requires two layers of power allocation to achieve high performance. Given that, a max-min fractional optimization problem is formulated to optimally distribute the power budget among the groups and the messages intended to the users of each group. Finally, a power allocation algorithm is designed with multiple Lagrangian multipliers to provide practical and sub-optimal solutions. The results show the high performance of the proposed scheme compared to other counterpart schemes.

To achieve multi-Gb/s data rates in 6G optical wireless access networks based on narrow infrared (IR) laser beams, a high-speed receiver with two key specifications is needed: a sufficiently large aperture to collect the required optical power and a wide field-of-view (FOV) to avoid strict alignment issues. This paper puts forward the systematic design and optimisation of multi-tier non-imaging angle diversity receivers (ADRs) composed of compound parabolic concentrators (CPCs) coupled with photodiode (PD) arrays for laser-based optical wireless communication (OWC) links. Design tradeoffs include the gain-FOV tradeoff for each receiver element and the area-bandwidth tradeoff for each PD array. The rate maximisation is formulated as a non-convex optimisation problem under the constraints on the minimum required FOV and the overall ADR dimensions to find the optimum configuration of the receiver bandwidth and FOV, and a low-complexity optimal solution is proposed. The ADR performance is studied using computer simulations and insightful design guidelines are provided through various numerical examples. An efficient technique is also proposed to reduce the ADR dimensions based on CPC length truncation. It is shown that a compact ADR with a height of$\leq 0.5$cm and an effective area of$\leq 0.5$cm2 reaches a data rate of 12 Gb/s with a half-angle FOV of 30° over a 3 m link distance.

The design of a compact high-speed and wide field of view (FOV) receiver is challenging due to the presence of two well-known trade-offs. The first one is the area-bandwidth trade-off of photodetectors (PDs) and the second one is the gain-FOV trade-off due to the use of optics. The combined effects of these two trade-offs imply that the achievable data rate of an imaging optical receiver is limited by its FOV, i.e., a rate-FOV trade-off. In this paper, we propose an imaging receiver design in the form of an array of (PD) arrays. To control the area-bandwidth trade-off, small PDs are used in an array of arrays structure instead of a single large PD. Moreover, to achieve a reasonable receiver FOV, we use an array of focusing lenses that focus the light individually on each inner PD array. The proposed array of arrays structure provides an effective method to control both gain-FOV trade-off (via an array of lenses) and area-bandwidth trade-off (via arrays of small PDs). We first derive a tractable analytical model for the signal-to-noise ratio (SNR) of an array of PDs that is equipped with a focusing lens assuming maximum ratio combining (MRC). Then, we extend the model to the proposed array of arrays structure and the accuracy of the analytical model is verified based on several Optic Studio-based simulations. Next, we formulate an optimization problem to maximize the achievable data rate of the imaging receiver subject to a minimum required FOV. The optimization problem is solved for two commonly used modulation techniques, namely, on-off keying (OOK) and direct current (DC) biased optical orthogonal frequency division multiplexing (DCO-OFDM) with variable rate quadrature amplitude modulation (QAM). Our results show the limits of high speed wide-FOV imaging receivers that can support mobility. For example, it is demonstrated that a data rate of$\sim 24$Gbps with a FOV of 15° is achievable using OOK with a total receiver size of 2 cm$\!\times \!\,\,2$cm.

Light amplification by stimulated emission of radiation (laser) sources has many advantages for use in high-data-rate optical wireless communications (OWCs). In particular, the low-cost and high-bandwidth properties of laser sources, such as vertical-cavity surface-emitting lasers (VCSELs), make them attractive for future indoor OWCs. In order to be integrated into future indoor networks, such lasers should conform to eye safety regulations determined by the International Electrotechnical Commission (IEC) standards for laser safety. In this article, we provide a detailed study of beam propagation to evaluate the received power of various laser sources, based on which and the maximum permissible exposure (MPE) defined by the IEC 60825-1:2014 Standard, we establish a comprehensive framework for eye safety analyses. This framework allows us to calculate the maximum allowable transmit power, which is crucial in the design of a reliable and safe laser-based wireless communication system. Initially, we consider a single-mode Gaussian beam and calculate the maximum permissible transmit power. Subsequently, we generalize this approach for higher mode beams. It is shown that the$M$-squared-based approach for analysis of multimode lasers ensures the IEC eye safety limits; however, in some scenarios, it can be too conservative compared to the precise beam decomposition method. Laser safety analyses with consideration of optical elements, such as lens and diffuser, as well as for the VCSEL array, have been also presented. Skin safety, as another significant factor of laser safety, has also been investigated in this article. We have studied the impacts of various parameters, such as wavelength, exposure duration, and the divergence angle of laser sources on the safety analysis by presenting insightful results.

In this paper, the design of a multiple-input multiple-output (MIMO) optical wireless communication (OWC) link based on vertical cavity surface emitting laser (VCSEL) arrays is systematically carried out with the aim to support data rates in excess of 1 Tb/s for the backhaul of sixth generation (6G) indoor wireless networks. The proposed design combines direct current optical orthogonal frequency division multiplexing (DCO-OFDM) and a spatial multiplexing MIMO architecture. For such an ultra-high-speed line-of-sight (LOS) OWC link with low divergence laser beams, maintaining alignment is of high importance. In this paper, two types of misalignment error between the transmitter and receiver are distinguished, namely, radial displacement error and orientation angle error, and they are thoroughly modeled in a unified analytical framework assuming Gaussian laser beams, resulting in a generalized misalignment model (GMM). The derived GMM is then extended to MIMO arrays and the performance of the MIMO-OFDM OWC system is analyzed in terms of the aggregate data rate. Novel insights are provided into the system performance based on computer simulations by studying various influential factors such as beam waist, array configuration and different misalignment errors, which can be used as guidelines for designing short range Tb/s MIMO OWC systems.

The demand for higher broadband speeds is ever increasing whereas the deployment of full fibre to the premises is slower than initially predicted and remains costly. Solutions exploiting the existing, ubiquitous, copper network and increasing its capacity would be highly beneficial in the near term. One approach is to use surface wave (SW) transmission mode to transmit signals over the existing copper cabling network. We present proof-of-concept experimental SW data transmission on twisted pair cables. A surface wave launcher for low GHz carrier frequency operation is designed and optimised. Experimentally, we demonstrate data rates in excess of 12 Gb/s in a 1.15-3.25 GHz band over a 6.1 m twisted pair cable with an average bit error rate of$2.25 \times 10 ^{-5}$, without coding or feedback implementation. Furthermore, higher frequency bands are tested with data rates up to 3.4 Gb/s displaying their potential for surface wave transmission. S-parameter measurements allow capacity estimations of SW data transmission on longer cable lengths using water-filling algorithms. Our calculations predict over 13 Gb/s capacity on a 100 m cable using a 3.5 GHz transmission bandwidth, this may be further extended by further increases to the bandwidth used for SW transmission.

In this paper, the performance of monostatic and bistatic passive ultra high frequency radio frequency identification (UHF RFID) systems under the effects of cascaded fading channels and interference is studied. The performance metric used is tag detection probability defined as the probability that the instantaneous received power is higher than the reader's sensitivity. A closed-form expression of the detection probability is derived using cascaded forward and backscatter fading channels and the reader antennas orientation relative to the tag. Furthermore, the performance of passive UHF RFID systems under reader-to-tag interference caused by both the desired RFID signal and multiple RFID interferers is analyzed, and the effect of constructive and destructive interferences is examined. In addition, the maximum reading range in ideal, multipath fading, and interfering environments is presented. To the best of our knowledge, this is the first work that provides a 3-D performance analysis of the passive UHF RFID systems under cascaded fading channels. The obtained results are very useful for the design and optimization of passive UHF RFID systems from an RF physical channel point of view.

In this paper the effect of partitioning arrays of transmitting antennas into spatially separated clusters on the condition number and capacity of MIMO wireless systems is examined using experimental channel measurements of an indoor MIMO-enabled distributed antenna system (DAS). It is first shown for a 3×2 MIMO system that distributing the transmit antennas into spatially separated clusters provides an improvement in channel conditioning (~1dB) and hence capacity, in line with previous findings. Next, a configuration with transmit antennas and 2 receive antennas is examined and it is found that when it is operated as a 6×2 MIMO system, it makes negligible difference to the conditioning of the channel whether the transmit antennas are grouped into 3 clusters of 2 antennas or 2 clusters of 3 antennas. The capacity varies by only a small amount (~%1) between the two clustering schemes, which can be accounted for by environment-specific signal-to-noise ratio (SNR) effects. It is then concluded that for the two typical indoor DAS scenarios tested here, if sufficient transmit diversity is provided (i.e. there are a relatively large number of transmit antennas compared to receive antennas), greater spatial distribution through increased clustering provides diminishing performance improvements. Given the typically lower installation cost of less distributed arrangements, they may then be a preferred option in commercial DAS deployments.

Radio Frequency Identification (RFID) system uses the principle of radiative power transfer between the reader and the tag antenna. Usually, it operates in a forward-link limited regime where the read range is limited by the ability to deliver power to the tag. Most of current researches consider the reader interrogation zone to be determined only by its read range assuming omni-directional antennas. However, the reliable interrogation zone also depends on interference effect, channel fading and the relative reader-tag antennas orientations. In this paper, we analyze the performance of the passive RFID systems taking into consideration reader antennas orientation and forward link fading for both desired signal and multiple RFID interferers. Using our model, we examine the effect of constructive and destructive (i.e. tag jamming) interferences in passive RFID system from the RF point of view. We also analyze the tag detection rate at different fading environments modeled by Rician distribution.

Airport terminals will increasingly require ubiquitous communications systems with high levels of computational power to provide the necessary intelligent automation to provide high quality services to passengers, stringent levels of safety and security that is as unobtrusive as possible, efficient processing of commercial goods and luggage, high quality information systems, airport transportation systems and appropriate support for in-house commercial ventures. These requirements will involve both fixed and mobile appliances, and hence an intelligent, adaptive, self-organizing and self-managing wired and wireless infrastructure will become an essential asset. This paper describes how The INtelligent Airport (TINA) project is therefore seeking to develop a new seamless wireless/wired ubiquitous infrastructure able to meet the above requirements. It will concentrate on how a passive RFID, using a radio over fiber-fed distributed antenna system can be used to provide location and tracking information on tagged assets over a wide area. By using the distributed antenna system, it is possible to suppress fading and nulls of the narrowband RFID channel and this allows the accuracy of RFID reads to be greatly improved and the area over which they can be read to be greatly increased. It also allows the use of the received signal strength indicator (RSSI) to provide a good measure of tag position.

The power consumption of radio over fiber fed distributed antenna networks is modeled. By optimization of the antenna unit RF output power, the power consumption is minimized. Optimized broadband multi-service and narrowband single service solutions are compared and it is shown that when more than 2 services are to be provided, the broadband multi-service system is more efficient.

An analysis of the sending rate of TCP control over Terabit per second rate links illustrates how future optical network characteristics, such as higher bitrates, network congestion, and larger data loads, would affect performance. We have implemented a model to allow increased sending rate for TCP. It is shown that even if the network bitrate is higher and the sending rate of TCP is scaled up, the throughput does not grow considerably, and latency remains one of the key parameters which must be reduced to improve performance.