The general approach to humanoid feet design considers the use of rectangular plate sole structures that are relatively stiff and compatible for flat terrain locomotion. Although this can be adequate the inability of these stiff feet to cope with small terrain irregularities, it makes them inappropriate for rough terrains. Toward improvement of humanoids feet this paper presents mechanism of new variable compliant humanoid feet which can provide functionality and adaptability to humanoids locomotion on uneven terrains. The proposed feet design introduces new toe mechanism in the feet with variable stiffness implemented using a leaf spring and rubber balls in series. We present the mechanism design and the implementation of the sensor, and discuss the estimation of variable stiffness range and coefficient of damping at sole. A prototype of the feet was built and experimental results are included to validate the feet design.

The development of variable impedance actuators (VIAs) has highlighted the need for proper control of passive impedance to attain suitable interaction performance. Until recently the regulation of the intrinsic impedance in VIAs is achieved in an open-loop model-based manner, mainly due to the lack of physical sensors capable of measuring impedance components such as stiffness and damping. Hence, the estimation of variable stiffness and damping has been explored, with the target to provide monitoring and feedback for potential closed loop control schemes. However, the use of the output of these estimators in the feedback control of variable impedance actuators has never been implemented/demonstrated in practice. This work contributes to the field with the development and experimental evaluation of a novel damping feedback control for a class of variable impedance compliant actuators able to realize a variable physical damping principle. The scheme is based on non-model-based damping estimation feedback to compensate model uncertainties in the action of an inner controller that uses a model-based friction estimator. Experimental results demonstrate the ability of the proposed scheme to replicate with good fidelity constant and time-varying damping levels.

The work presents the development and evaluation of a novel foot sole for humanoid robots. For humanoid locomotion the foot sole is important for absorbing impacts. In contrast to the simple planar rubber pad foot sole that is conventionally used in humanoid robots this paper introduces a new foot sole design in which the dissipation of energy during collision is done effectively using a viscous air damping sole mechanism that provides better reduction of the ground impact forces. The paper describes the principle of the foot sole and provides details of its design and implementation. Experimental trials were performed with the child size humanoid robot, COMAN, wearing the proposed feet to validate their performance during landing and walking. The results demonstrate that the proposed new passive damping mechanism can reduce effectively the ground reaction impact forces and oscillations while maintaining the foot/body posture.

The balance control of humanoid robots against external perturbations is a fundamental prerequisite for operating in unstructured environments where physical interaction may unexpectedly occur. These balancing actions can be very demanding in terms of power and torque requirements for ankle joints especially after strong and sudden impacts. In this work, an optimal control problem is formulated for the linearized inverted pendulum model to reduce the peak power requirements during ankle balancing strategy. This optimal control which reduces peak torque and power is computed numerically and approximated by a piecewise linear function of the states called the approximate optimal compliance regulator. The balancing ability of this compliance regulator is evaluated against other optimal compliance methods. The stability of the linearly switching approximated optimal compliance regulator is determined from practical perspective using quadratic stability and parameter dependent Lyapunov functions. The efficacy of the proposed stabilizer is validated for a compliant humanoid.

This paper presents a sufficient condition to establish the existence of unique equilibrium points for three types of gravity compensation controller when applied to over-actuated systems. As compared to the existing work, this paper extends the current theory by introducing feedback gain matrices that are not constrained to being diagonal and positive definite. The inherently COmpliant huMANoid (COMAN) served as a platform for the validation of the designed gravity compensation controller that employed reference link positions. The displayed experimental results provide evidence of successful link tracking of sinusoidal references on a humanoid system composed of series elastic actuators.

The incorporation of passive compliance in robotic systems could improve their performance during interactions and impacts, for energy storage and efficiency, and for general safety for both the robots and humans. This paper presents the recently developed COMpliant huMANoid COMAN. COMAN is actuated by passive compliance actuators based on the series elastic actuation principle (SEA). The design and implementation of the overall body of the robot is discussed including the realization of the different body segments and the tuning of the joint distributed passive elasticity. This joint stiffness tuning is a critical parameter in the performance of compliant systems. A novel systematic method to optimally tune the joint elasticity of multi-dof SEA robots based on resonance analysis and energy storage maximization criteria forms one of the key contributions of this work. The paper will show this method being applied to the selection of the passive elasticity of COMAN legs. The first completed robot prototype is presented accompanied by experimental walking trials to demonstrate its operation.

This paper presents an Octopus inspired walking robot with pneumatic muscle actuator (PMA) driven continuum arms. Each arm is made up of 4 longitudinally arranged PMAs, consistent with octopus arm anatomy. We first present the design and construction of a single continuum arm followed by its modeling and experimental validation. The design of the walking robot is then presented followed by details of extended dynamic model describing the full walking robot with four arms. Basic control architecture is introduced for the robot to achieve walking motion and experimental results analyzed. Initial results show good agreement between the experimental results and simulation results.

A legged robot has to deal with environmental contacts every time it takes a step. To properly handle these interactions, it is desirable to be able to set the foot compliance. For an actively-compliant legged robot, in order to ensure a stable contact with the environment the robot leg has to be passive at the contact point. In this work, we asses some passivity and stability issues of the actively-compliant leg of the quadruped robot HyQ, which employs a highperformance cascade compliance controller. We demonstrate that both the nested torque loop performance as well as the actuator bandwidth have a strong influence in the range of virtual impedances that can be passively rendered by the robot leg. Based on the stability analyses and experimental results, we propose a procedure for designing cascade compliance controllers. Furthermore, we experimentally demonstrate that the HyQ's actively-compliant leg is able to reproduce the compliant behavior presented by an identical but passively-compliant version of the same leg.

Keeping balance is the main concern for humanoids in standing and walking tasks. This paper endeavors to acquire optimal ankle stabilization methods for humanoids with passive and active compliance and explain ankle balancing strategy from the compliance regulation perspective. Unlike classical stiff humanoids, the compliant ones can control both impedance and position during task operation. Optimal compliance regulation is resolved to maximize the stability of the humanoids. The linearized model is proposed to obtain the optimal ankle impedance for stabilizing against impacts. The nonlinear model is proposed as well and compared with the linear one. The proposed methods are validated by experiments on an intrinsically compliant humanoid using passivity based admittance and impedance controllers both in joint and Cartesian space.

This paper provides stability analyses for two different types of desired gravity compensation controllers, employing both motor and link feedback, and describes a means by which these controllers can be used to control a compliant humanoid robot in order to ensure the successful execution of walking trajectories. Given the challenging task of controlling compliant bipedal systems, owing to their possession of underactuated degrees of freedom, the full actuator and link dynamics are accounted for. The proposed walking strategy involves a process of switching between three distinct controllers which is contingent upon the force feedback provided by the force/torque sensors embedded in the robot's feet. These controllers were tuned using a simulation model of the robot and were then implemented on the compliant COMAN legs, whose performance of walking confirms the controllers' stability, in addition to the walking scheme's efficacy.

This paper presents the design of a novel compliant joint for high performance mobility. The design principle of the joint is based on an asymmetric compliant antagonistic scheme which is actuated by two motors of different power capability and efficiency. Torques from the two motors are transmitted to the joint through two elastic elements of different stiffness and energy storage capacity. The proposed compliant joint design combines high power performance, large energy storage capacity and physical resilience all necessary features for performing high performance mobility such as agile locomotion. The paper introduces the principle of operation, the design and mechanical implementation of the joint. Preliminary experimental trials demonstrate the joint performance in a single degree of freedom leg prototype system.

This paper is concerned with the design of a control strategy for variable stiffness actuators in series configuration, exploiting the lever concept to adjust the stiffness at the transmission. A control strategy based on gain scheduling is proposed, which is able to regulate both stiffness and position at output link. The gain scheduling is designed based on a set of linear quadratic regulators (LQRs), because LQR's inherent robustness properties can accommodate significant variation in the actuation plant parameters. The link positioning relies on continuous adjustment of the control effort based on the current transmission stiffness; the stiffness perceived at the output link is regulated through combined action of the transmission stiffness and the positioning gains of the scheduling strategy. The effectiveness of the controller is verified in simulation and experiments on the actuator with adjustable stiffness. The overall strategy has been proven to be locally stable.

Variable stiffness actuators (VSAs) have been introduced to improve, at the design level, the safety and the energy efficiency of the new generation of robots that have to interact closely with humans. A wide variety of design solutions have recently been proposed, and a common factor in most of the VSAs is the introduction of a flexible transmission with varying stiffness. This, from the control perspective, usually implies a nonlinear actuation plant with varying dynamics following time-varying parameters, which requires more complex control strategies with respect to those developed for flexible joints with a constant stiffness. For this reason, this paper proposes an approach for controlling the link position and stiffness of a VSA. The link positioning relies on a LQR-based gain scheduling approach useful for continuously adjusting the control effort based on the current stiffness of the flexible transmission. The stiffness perceived at the output link is adjusted to match the varying task requirements through the combination of the positioning gains and the mechanical stiffness. The stability of the overall strategy is briefly discussed. The effectiveness of the controller in terms of tracking performance and stiffness adjustment is verified through experiments on the Actuator with Adjustable Stiffness (AwAS).

Continuum structures with a very high or infinite number of degrees of freedom (DOF) are very interesting structures in nature. Mimicking this kind of structures artificially is challenging due to the high number of required DOF. This paper presents a kinematic and dynamic model for an underwater robotic manipulator inspired by Octopus vulgaris. Then, a prototype arm inspired by live octopus is presented and the model validated experimentally. Initial comparisons of simulated and experimental results show good agreement.

Robots are frequently modeled as rigid body systems, having torques as input to their dynamics. A high-performance low-level torque source allows us to control the robot/environment interaction and to straightforwardly take advantage of many model-based control techniques. In this paper, we define a general 1-DOF framework, using basic physical principles, to show that there exists an intrinsic velocity feedback in the generalized force dynamics, independently of the actuation technology. We illustrate this phenomena using three different systems: a generic spring-mass system, a hydraulic actuator, and an electric motor. This analogy helps to clarify important common aspects regarding torque/force control that can be useful when designing and controlling a robot. We demonstrate, using simulations and experimental data, that it is possible to compensate for the load motion influence and to increase the torque tracking capabilities.

This paper presents a new three dimensional kinematic and dynamic model for variable length continuum arm robotic structures using a novel shape function-based approach. The model incorporates geometrically constrained structure of the arm to derive its deformation shape function. It is able to simulate spatial bending, pure elongation, and incorporates a new stiffness control feature. The model is validated through numerical simulations, based on a prototype continuum arm, that yields physically accurate results.

This paper presents a new three dimensional (3D) kinematic model based on mode shape functions (MSF) for multisection continuum arms. It solves the singularity problems associated with previous models and introduces a novel approach for intuitively deriving exact, singularity-free MSFs, thus avoiding mode switching schemes and simplifying error models. The model is able to simulate spatial bending, pure elongation/contraction, and introduces inverse orientation kinematics for the first time to multisection continuum arms. Also, it carefully accounts for physical constraints in the joint space to provide enhanced insight into practical mechanics, and produces correct results for both forward and inverse kinematics. The model is validated through simulations, based on a prototype continuum robotic arm. Proposed approach is applicable to a broad spectrum of continuum robotic arm designs.

The processes of nuclear clean-up, dismantling and decontamination are highly hazardous, but in many instances, particularly where the facility is older there has been little provision for automation, and human intervention is necessary. The paper describes a prototype design of a teleoperational rig for retrieval of radioactive material (spent Magnox fuel) from underwater storage ponds. The system uses a combination of the traditional man-handled manipulation pole combined with new pneumatic muscle actuators. The paper considers the design requirement, the technology and the system performance in dry test operations.

This work reports on the construction of components for a humanoid robot powered by a new low mass, high power weight and volume actuation system, called the pneumatic muscle actuator (PMA). In addition to their power and force capabilities the PMA, being pneumatic, produces a more natural human muscle like contact and as such can be considered a soft actuation system with the inherent safety implication when working in close proximity to humans. The integration and testing of the performance of the component sections is also considered to show how these structures and actuators can be combined to produce the various systems needed for a low mass humanoid and the potential for future application in humanoid and other robotic fields.

Bipedal locomotion and particularly the human gait is a highly automated and complex process involving large numbers of actuators. Unfortunately actuator technology is an area of robotics with many conflicting requirements such as: high power density, high power to weight ratio, rapid response, accurate repeatable control, cleanliness, high efficiency, and low cost, which make selection complex. Pneumatic muscle actuators (PMA) [based on the McKibben Muscle] which can provide position and force control better than 1% have been applied to upper limbs with some success and with contractile forces in excess of 1000N (in units weighing less than 50g) there is considerable potential for use in bipedal locomotion. This paper will explore the design of a bipedal robot to take advantage of the potential of these actuators. Muscle co-ordination and control sequences will be considered for striding and standing activities and it will be shown that in terms of the energy requirements PMAs are very capable of providing a reliable bipedal drive source with linear actuation, low mass, fast response, compliant energy storage and simple construction.

Problems with the control and compliance of pneumatic systems have prevented their widespread use in advanced robotics. However, their compactness, power/weight ratio and inherent safety are factors that could potentially be exploited in sophisticated dexterous manipulator designs. These advantages have lead to the development of novel actuators such as the McKibben Muscle, Rubbertuator, Flexator, Romac and pneumatic muscle actuators (PMA). However, the nonlinearities in these systems still limit their controllability. This paper considers the development of an adaptive controller for bi-muscular PMA system. Control of these muscles is explored via adaptive pole-placement controllers. Experimental results indicate that accurate position control /spl plusmn/2/spl deg/ is feasible, with power/weight outputs in excess of 1 kW/kg at 250 kPa being possible.

Problems with the control and compliance of pneumatic systems have prevented their widespread use in advanced robotics. However, their compactness, power/weight ratio and inherent safety are factors that could potentially be exploited in sophisticated dexterous manipulator designs. This paper considers the development of a new high power/weight and power/volume braided pneumatic muscle actuator (PMA) having considerable power output potential, combined with controllable motion and inherent compliance to prevent damage to handled objects. Control of these muscles is explored via adaptive pole-placement controllers. Experimental results indicate that accurate position control /spl plusmn/1/spl deg/ is feasible with power/weight outputs in excess of 1 kW/kg at 200 kPa being possible.>