LoRa has emerged as a crucial technology that provides ubiquitous connectivity for geographically distributed Internet of Things devices. LoRa employs linear Chirp Spread Spectrum (CSS) modulation in its physical layer to enable long-range communication. Recently, nonlinear chirps have been proposed to replace linear chirps in CSS, to enhance the capacity and scalability of LoRa technology. However, the characteristics and advantages of nonlinear chirps are not yet fully understood. To unleash the potential of nonlinear CSS modulation, this paper presents a comprehensive theoretical and experimental analysis of the nonlinear chirp, focusing on key aspects such as noise resilience, error correction, curvature selection, and bandwidth expansion. Our findings reveal that nonlinear chirps are intrinsically more resilient to noise than linear chirps. Moreover, nonlinear chirps typically exhibit a single-place demodulation error under strong noise conditions, which has informed our development of a simple yet effective error correction design. Additionally, users should carefully manage nonlinear chirp curvatures and signal power compensation to avoid distortion while benefiting from the bandwidth expansion offered by nonlinear chirps. Building on these insights, we further refine nonlinear CSS modulation and implement our optimized design on US-RPs. Field experiments demonstrate that our design achieves significant performance improvements, marking a step forward in the practical application of nonlinear CSS modulation in LoRa networks.

Wind speed monitoring is crucial for environmental management and forecasting. However, current solutions often struggle with high power consumption, especially at the end device, which typically has a sensor and wireless radios with limited battery capacity. To this end, we present WindScatter, an ultra-low-power, long-range, and large-scale wind speed monitoring system. WindScatter adopts the Integrated Sensing and Communication (ISAC) paradigm to enable low-power operation. It reuses the sensed data for communication by leveraging a TMR (Tunnel Magneto-Resistance) switch sensor to measure the wind speed information and control the backscatter communication simultaneously, thus avoiding the need for analog-to-digital conversion and a microcontroller for communication control. Our hardware-software co-design enables accurate measurements and stable concurrent transmission. We implement WindScatter and conduct extensive experiments and case studies to evaluate its performance. Results show that WindScatter supports measurements of all wind speed levels on the Extended Beaufort scale, from 1.5 m/s to 60 m/s, with an average error rate of 0.78%. WindScatter can sense and transmit wind speed data at a distance of 800 m with a power consumption of 136.5$\mu$W. Compared with commodity devices, WindScatter achieves comparable measurement range and accuracy while reducing cost by$91.5\times$and power consumption by$8,791\times$.

Electrode coating measurement is a crucial task in practical lithium-ion battery systems, where the thickness and refractive index of the electrode coating directly reflect the battery's quality, energy density, capacity, and lifespan. In this paper, we propose the design, implementation, and evaluation of BatTera, the practical system for an accurate, high-resolution, non-destructive, and safe electrode coating measurement, with the ability to simultaneously measure coating thickness and refractive index. BatTera's contributions are twofold. Firstly, we build a comprehensive mathematical model that characterizes the arrival time of echo signals from both sides of the electrode coating by thoroughly analyzing the electrode structure based on “coating-foil-coating”. This model serves as a theoretical foundation guiding the measurement of coating thickness and refractive index. Secondly, we propose a series of effective signal-processing algorithms to address the practical challenges of double-side coating misalignment and deformation interference, thus adaptive improving the signal-to-noise ratio of Terahertz signals and pushing BatTera one big step closer to real adoptions. We implement BatTera based on the commercial Terahertz device QT-TO1000 and conduct extensive experiments using five types of cathode electrode samples in three different sizes, collected from one of the world's largest new energy battery manufacturers. The results show that BatTera achieves high measurement accuracy with a mean average error of 6.106$\upmu$m for thickness and 0.230 for refractive index.

Carrier interference is a fundamental research challenge in backscatter systems. Existing solutions leverage frequency shifting or full duplex designs to mitigate carrier interference in the analog or digital domain. However, these solutions introduce extra spectrum usage, protocol overhead, and power consumption, all of which are undesirable in backscatter systems. In this paper, we revisit polarization mismatch and propose Lotus, a low-cost analog design to combat carrier interference for backscatter systems. Lotus comprises a novel antenna design and a backscatter tag design. At runtime, Lotus antenna replaces the receiver default antenna to cancel out the carrier interference, without any protocol or hardware overhead. Lotus tag mitigates the power loss caused by polarization mismatch and remains compatible with all existing backscatter radios. Experimental results show that Lotus achieves comparable cancellation gain (i.e., 42 dB) with the state-of-the-art frequency-shifting baseline. Meanwhile, Lotus outperforms the baseline by 2× and 6.5× in spectrum and power efficiency, respectively. Additionally, Lotus achieves comparable performance to the frequency shifting baseline regarding backscatter range and throughput across three backscatter technologies, including Wi-Fi, Bluetooth, and LoRa.

In recent years, there has been a growing focus on developing Low Power Wide Area Network (LPWAN) protocols, especially within the LoRa research community. However, the research community for NB-IoT, another crucial LPWAN technology, has not experienced comparable expansion due to the absence of a functional and adaptable software-defined radio (SDR) implementation. To address this gap, we present SoftNB, the first fully functional physical layer SDR implementation for NB-IoT. SoftNB conforms to the latest 3GPP standards and features an efficient and effective signal processing pipeline to mitigate time, frequency, and phase offsets during transmission and reception. Additionally, SoftNB is compatible with various SDR platforms, including USRP, HackRF One, and RTL-SDR Dongle. Extensive evaluations of SoftNB demonstrate its superior performance. Compared to the state-of-the-art baseline, SoftNB achieves an 8× reduction in Block Error Rate (BLER) when the number of repetitions is set to 4 at a distance of 450 meters.

Semi-supervised learning performs accurate segmentation by effectively leveraging unlabeled data. Most existing methods struggle to capture complex global data distribution, which is particularly important for medical images characterized by intricate background structures and ambiguous boundaries. Class prototypes are commonly used to represent the essential semantic representation of each class. Most prototype methods construct a single prototype vector per class using convolutional neural networks (CNNs), thereby neglecting both distribution modeling and intra-class variability. To address these issues, we propose a diffusion and spatial prototype learning method (DSP) for semi-supervised medical image segmentation. Firstly, the Image-to-Segmentation Diffusion Model (ISDM) generates pseudo-labels rich in distribution information from the original image. Secondly, the diffusion network is combined with a Convolutional Segmentation Network (CSN) to simultaneously learn data distribution and anatomical details. Thirdly, class prototypes are constructed at the voxel level and combined with the diffusion model to make them spatially aware and incorporate global distribution information. Extensive experiments on three benchmark medical image datasets (left atrium and brain tumor) show that our method achieves state-of-the-art performance, validating its effectiveness. Code is available at: https://github.com/Lianyuan-Yu/DSP.

Parallelizing passive Radio Frequency Identification (RFID) reading is an arguably crucial, yet unsolved challenge in modern IoT applications. Existing approaches remain limited to time-division operations and fail to read multiple tags simultaneously. In this paper, we introduce QuinID, the first frequency-division multiple access (FDMA) RFID system to achieve fully parallel reading. We innovatively exploit the frequency selectivity of the tag antenna rather than a conventional digital FDMA, bypassing the power and circuitry constraint of RFID tags. Specifically, we delicately design the frequency-selective antenna based on surface acoustic wave (SAW) components to achieve extreme narrow-band response, so that QuinID tags (i.e., QuinTags) operate exclusively within their designated frequency bands. By carefully designing the matching network and canceling various interference, a customized QuinReader communicates simultaneously with multiple QuinTags across distinct bands. QuinID maintains high compatibility with commercial RFID systems and presents a tag cost of less than 10 cents. We implement a 5-band QuinID system and evaluate its performance under various settings. The results demonstrate a fivefold increase in read rate, reaching up to 5000 reads per second.

Millimeter-wave (mmWave) sensing technology holds significant value in human-centric applications, yet the high costs associated with data acquisition and annotation limit its widespread adoption in our daily lives. Concurrently, the rapid evolution of large language models (LLMs) has opened up opportunities for addressing complex human needs. This paper presents mmExpert, an innovative mmWave understanding framework consisting of a data generation flywheel that leverages LLMs to automate the generation of synthetic mmWave radar datasets for specific application scenarios, thereby training models capable of zero-shot generalization in real-world environments. Extensive experiments demonstrate that the data synthesized by mmExpert significantly enhances the performance of downstream models and facilitates the successful deployment of large language models for mmWave understanding.

Wi-Fi is the de facto standard for providing wireless access to the Internet in the 2.4 GHz ISM band. Tens of billions of Wi-Fi devices (e.g., smartphones) have been shipped worldwide with limited types of wireless radios operating only when Wi-Fi connectivity is available, making it challenging to access data in heterogeneous IoT devices. However, the direct connection between Wireless Personal Area Network (WPAN) technologies, such as Bluetooth, and Wi-Fi presents challenges due to the inherent distinct physical layer. In our work, a novel communication method called BlueWi has been introduced, which serves as a cross technology communication method that enables BLE devices to establish connections and engage in communication with Wi-Fi based WPAN networks. We let BLE signals hitchhike on ongoing Wi-Fi signals, enabling Wi-Fi to recognize specific BLE signal waveforms in the frequency domain. By analyzing the decoded Wi-Fi payload, BlueWi can retrieve the BLE data, ensuring this method remains fully compatible with existing commodity Wi-Fi hardware. The direct sequence spread spectrum scheme is appended to handle general BLE frames and can be considered as “COPY” operation, which allows for better correlation and detection of the signal at the receiver. Evaluations conducted using both USRP and commodity devices have demonstrated that BlueWi can achieve concurrent wireless communication from BLE commercial chips to Wi-Fi networks with a frame reception rate exceeding 96%.

Whilesmalldrone video streaming systems create unprecedented video content, they also place a power burden exceeding 20% on the drone's battery, limiting flight endurance. We present${\sf Mighty}$, a hardware-software solution to minimize the power consumption of a drone's video streaming system by offloading power overheads associated with both video compression and transmission to a ground controller.${\sf Mighty}$innovates a high performance co-design among:(1)a ring oscillator-based, ultra-low power backscatter radio;(2)a spectrally-efficient, non-linear, low-power physical layer modulation and multi-chain radio architecture; and(3)a lightweight video compression codec-bypassing software design. Our co-design exploits synergies among these components, resulting in joint throughput and range performance that pushes the known envelope. We prototype${\sf Mighty}$on PCB board and conduct extensive field studies both indoors and outdoors. The power efficiency of${\sf Mighty}$is about 16.6 nJ/bit. A head-to-head comparison with aDJI Mini2drone's default video streaming system shows that${\sf Mighty}$achieves similar throughput at a drone-to-controller distance of up to 150 meters, with 34–55× improvement of power efficiency than WiFi-based video streaming solutions.

Frequency switching is a fundamental capability for wireless communication systems. However, this capability is significantly constrained in backscatter systems. The difficulty is to generate tunable high-frequency modulation signals on a backscatter tag at an acceptable power budget. In this paper, we present Twaltz, a new design paradigm for backscatter communication that enables frequency switching across large frequency bands. By exploiting a low-power semiconductor device, i.e., tunnel diode, and carefully addressing its physical features, Twaltz generates oscillation signals up to 1.2 GHz while maintaining micro-watt level power consumption. Twaltz further facilitates on-tag oscillation signal stabilization and programmable oscillation frequency tuning. We prototype Twaltz on a PCB board, demonstrating its efficiency in cross-band communication for LoRa backscatter, and verifying its performance in concurrent transmission, channel hopping, and data transmission.

Semi-supervised learning leverages insights from unlabeled data to enhance generalizability of the model, thereby decreasing the dependence on extensive labeled datasets. Most existing methods overly focus on local representations while neglecting the learning of global structures. On the one hand, given that labeled and unlabeled images are presumed to originate from the same distribution, it is probable that similar regional features observed in both types of images correspond to the same label. Current label propagation techniques, which predominantly propagate label information through the construction of graph structures or similarity matrices, heavily depend on localized information and are prone to converge to local optima. In contrast, optimal transport considers the entire distribution. This facilitates more comprehensive and efficient label propagation. On the other hand, current consistency regularization-based methods focus on the local view, we believe learning from a global geometric view may capture more information. Geometric moment information of the sample itself can constrain the overall geometric structure. Inspired by these observations, this paper introduces a semi-supervised medical image segmentation framework that integrates optimal transport and central moment consistency regularization (OTCMC) from a global perspective. Firstly, we pass label information from labeled data to unlabeled data by optimal transport. Secondly, we incorporate central moment consistency regularization to focus the network on the geometric structure of images. Our method achieves the state-of-the-art (SOTA) performance on a series of datasets, including the NIH pancreas, left atrium, brain tumor, and skin lesion dermoscopy datasets.

Backscatter is an enabling technology for battery-free sensing in today’s Artificial Intelligence of Things (AIOT). Building a backscatter sensing system, however, is a daunting task, due to two obstacles: the unaffordable power consumption of the microprocessor and the coexistence with the ambient carrier’s traffic. In order to address the issues, we present Leggiero, the first-of-its-kind analog WiFi backscatter with payload transparency, and its enhanced version, Leggiero+. A specially designed circuit based on the varactor diode directly converts fast-varying analog sensor signals into the RF (radio frequency) signal phase, eliminating the need for a microprocessor to interface between the radio and the sensor. By precisely locating the WiFi packet’s extra long training field (LTF) section and carefully designing the reference circuit, Leggiero embeds the analog phase into the channel state information (CSI). A commodity WiFi receiver without hardware modification can simultaneously decode the WiFi and the sensor data. We implement and evaluate Leggiero and Leggiero+ under varied settings. Results show the tag’s power consumption (excluding the power of the peripheral sensor module) is$30\mu $W at a 400Hz sampling rate,$4.8\times $and$4\times $lower than the state-of-the-art WiFi backscatter schemes. Leggiero+ demonstrates enhanced throughput, communication range, and analog signal reproduction accuracy. Our design supports a variety of sensing applications, while maintaining the WiFi carrier’s throughput performance.

WiFi-based device localization is a key technology for smart applications, while most of which rely on LoS signals to work. However, in real-world indoor environments, very few LoS signals are usable for accurate localization. This article presents Bifrost , a novel hardware-software co-design to cope with this practical problem. The core idea of Bifrost is to reinvent WiFi signals to provide sufficient LoS signals. Specifically, we present a low-cost plug-in design of leaky wave antenna (LWA) that can generate orthogonal polarized signals: On the one hand, LWA disperses signals of different frequencies to different angles, thus providing AoA information for the localized target. On the other hand, the target further leverages the antenna polarization mismatch to distinguish AoAs from different LWAs. Besides, fine-grained information in CSI is exploited to mitigate multipath and noise. Besides, a dedicated Kalman filter is proposed to facilitate the cooperation of Bifrost and SpotFi, a state-of-the-art approach, to enhance the availability and accuracy of SpotFi. The evaluation results show that the median localization error of Bifrost is 0.81 m, 52.35% less than that of SpotFi. When combined with Bifrost to work in realistic settings, SpotFi can reduce the localization error by 33.54%.

LoRa networks operating in a star topology, this configuration creates a single point of failure and may limit scalability and reliability in areas that are large and geographically dispersed. In order to improve the overall transmission capabilities of the network, recent studies show that adding LoRa to the ZigBee devices effectively disseminates network management. By doing so, the strengths of both technologies can be leveraged, with LoRa serving as the long-range transmitter and ZigBee functioning as the mesh network. In this study, we present LoBee, a novel bidirectional communication method between LoRa and ZigBee that relies on Physical-Layer Cross-Technology Communication. Despite the fact that LoRa and ZigBee utilize different modulation techniques, ZigBee devices can detect and recognize LoRa chirps through the process of sampling the received signal strength. For the transmissions from ZigBee to LoRa devices, we carefully select the input chips to generate specific waveforms, where LoBee detects the preamble of a ZigBee frame based on the locations of the repeated peaks. Our evaluation, which was conducted using USRP and commodity devices, demonstrates that LoBee is capable of achieving concurrent bidirectional wireless communications, with a data rate of approximately 639.38 bits per second from LoRa to ZigBee and from ZigBee to LoRa with more than 90% frame reception rate in the 2.4 GHz frequency band.

We present MAF, a novel acoustic sensing approach that leverages the commodity hardware in bone conduction earphones for hand-to-face gesture interactions. Briefly, by shining audio signals with bone conduction earphones, we observe that these signals not only propagate along the surface of the human face but also dissipate into the air, creating an acoustic field that envelops the individual’s head. We conduct benchmark studies to understand how various hand-to-face gestures and human factors influence this acoustic field. Building on the insights gained from these initial studies, we then propose a deep neural network combined with signal preprocessing techniques. This combination empowers MAF to effectively detect, segment, and subsequently recognize a variety of hand-to-face gestures, whether in close contact with the face or above it. Our comprehensive evaluation based on 22 participants demonstrates that MAF achieves an average gesture recognition accuracy of 92% across ten different gestures tailored to users’ preferences.

LoRa has emerged as a crucial technology that provides ubiquitous connectivity for geographically distributed Internet of Things devices. LoRa employs linear Chirp Spread Spectrum (CSS) modulation in its physical layer to enable long-range communication. Recently, nonlinear chirp has been proposed to replace linear chirp in CSS, to enhance the capacity and scalability of LoRa technology. However, the characteristics and advantages of nonlinear chirps are not yet fully understood. To unleash the potential of nonlinear CSS modulation, this paper presents a comprehensive theoretical and experimental analysis of the nonlinear chirp, focusing on key aspects such as noise resilience, error correction, and bandwidth expansion. Our findings reveal that nonlinear chirps are intrinsically more resilient to noise than linear chirps. Moreover, nonlinear chirps typically exhibit a single-place demodulation error under strong noise conditions, which has informed our development of a simple yet effective error correction design. Additionally, users should carefully manage signal power compensation to avoid distortion while benefiting from the bandwidth expansion offered by nonlinear chirps. Building on these insights, we further refine nonlinear CSS modulation and implement our optimized design on USRPs. Field experiments demonstrate that our design achieves significant performance improvements, marking a step forward in the practical application of nonlinear CSS modulation in LoRa networks.

The millimeter-wave (mmWave) radar has been exploited for gesture recognition. However, existing mmWave-based gesture recognition methods cannot identify different users, which is important for ubiquitous gesture interaction in many applications. In this paper, we propose GesturePrint, which is the first to achieve gesture recognition and gesture-based user identification using a commodity mmWave radar sensor. GesturePrint features an effective pipeline that enables the gesture recognition system to identify users at a minor additional cost. By introducing an efficient signal preprocessing stage and a network architecture GesIDNet, which employs an attention-based multi-level feature fusion mechanism, GesturePrint effectively extracts unique gesture features for gesture recognition and personalized motion pattern features for user identification. We implement GesturePrint and collect data from 17 participants performing 15 gestures in a meeting room and an office, respectively. GesturePrint achieves a gesture recognition accuracy (GRA) of 98.87% with a user identification accuracy (UIA) of 99.78% in the meeting room, and 98.22% GRA with 99.26% UIA in the office. Extensive experiments on three public datasets and a new gesture dataset show GesturePrint's superior performance in enabling effective user identification for gesture recognition systems.

The design of Low Power Wide Area Network (LPWAN) protocols has attracted increasing attention in recent years, particularly within the LoRa research community. However, NB-IoT, another critical LPWAN technology, has not seen similar growth in its research community due to the lack of a functional and flexible software-defined radio (SDR) implementation. To address this gap, we present SoftNB, the first fully functional physical layer SDR implementation for NB-IoT. SoftNB conforms to the latest 3GPP standards and features an efficient and effective signal processing pipeline to mitigate time, frequency, and phase offsets during transmission and reception. Additionally, SoftNB is compatible with various SDR platforms, including USRP, HackRF One, and RTL-SDR Dongle. Extensive evaluations of SoftNB demonstrate its superior performance. Compared to the state-of-the-art baseline, SoftNB achieves an$8\times$reduction in Block Error Rate (BLER) when the number of repetitions is set to 4 at a distance of 450 meters.

Wave-based human tracking is a key enabling technology for smart applications. Most of the existing works on this topic employ the conventional approach of device-free object localization, which treat any person as a general moving target rather than distinguish different persons. As a result, the existing approaches have poor performance in the scenarios of multi-person tracking, especially when there are crossovers among different persons’ trajectories. This paper presents mMTAI, a novel approach for multi-person tracking with a mmWave radar. By exploiting mmWave sensing to capture a human’s biometric features, MMTAI augments mmWave radar based human tracking with the ability of identifying different persons. Specifically, MMTAI is able to sense persons’ scalp responses to the signals and their head-shoulder distances, which are then continuously mapped to their trajectories using a bipartite matching algorithm. We implement MMTAI with a commercial mmWave radar and evaluate its performance under various settings. The results show that in the multi-person tracking scenarios, mmTAI has a median tracking error of 12.33 cm, which is $35.88 \%$ lower than that of the state-of-the-art approach.

Heart rate recovery (HRR) within the initial minute following exercise is a widely utilized metric for assessing cardiac autonomic function in individuals and predicting mortality risk in patients with cardiovascular disease. However, prevailing solutions for HRR monitoring typically involve the use of specialized medical equipment or contact wearable sensors, resulting in high costs and poor user experience. In this paper, we propose a contactless HRR monitoring technique, mmHRR, which achieves accurate heart rate (HR) estimation with a commercial mmWave radar. Unlike HR estimation at rest, the HR varies quickly after exercise and the heartbeat signal entangles with the respiration harmonics. To overcome these hurdles and effectively estimate the HR from the weak and non-stationary heartbeat signal, we propose a novel signal processing pipeline, including dynamic target tracking, adaptive heartbeat signal extraction, and accurate HR estimation with composite sliding windows. Real-world experiments demonstrate that mmHRR exhibits exceptional robustness across diverse environmental conditions, and achieves an average HR estimation error of 3.31 bpm (beats per minute), 71% lower than that of the state-of-the-art method.

Backscatter is an enabling technology for battery-free sensing in industrial IoT applications. For the purpose of full coverage of numerous tags in the deployment area, one often needs to deploy multiple readers, each of which is to communicate with tags within its communication range. But the actual backscattered signals from a tag are likely to reach a reader outside its communication range, causing undesired interference. Conventional approaches for interference avoidance, either TDMA or CSMA based, separate the readers’ media accesses in the time dimension and suffer from limited network throughput. In this paper, we propose Trident, a novel backscatter tag design that enables interference avoidance with frequency-space division. By incorporating a tunable bandpass filter and multiple terminal loads, a Trident tag is able to detect its channel condition and adaptively adjust the frequency band and the power of its backscattered signals, so that all the readers in the network can operate concurrently without being interfered. We implement Trident and evaluate its performance under various settings. The results demonstrate that Trident enhances the network throughput by 3.18×, compared to the TDMA based scheme.

The elderly over 65 accounts for 80% of COVID deaths in the United States. In response to the pandemic, the federal, state governments, and commercial insurers are promoting video visits, through which the elderly can access specialists at home over the Internet, without the risk of COVID exposure. However, the current video visit practice barely relies on video observation and talking. The specialist could not assess the patient's health conditions by performing auscultations.

This paper presents the design, implementation, and evaluation of MagWear, a novel biomagnetism-based system that can accurately and inclusively monitor the heart rate and respiration rate of mobile users with diverse skin tones. MagWear's contributions are twofold. Firstly, we build a mathematical model that characterizes the magnetic coupling effect of blood flow under the influence of an external magnetic field. This model uncovers the variations in accuracy when monitoring vital signs among individuals. Secondly, leveraging insights derived from this mathematical model, we present a softwarehardware co-design that effectively handles the impact of human diversity on the performance of vital sign monitoring, pushing this generic solution one big step closer to real adoptions. We have implemented a prototype of MagWear on a two-layer PCB board and followed IRB protocols to conduct system evaluations. Our extensive experiments involving 30 volunteers demonstrate that MagWear achieves high monitoring accuracy with a mean percentage error (MPE) of 1.55% for heart rate and 1.79% for respiration rate. The head-to-head comparison with Apple Watch 8 further demonstrates MagWear's consistently high performance in different user conditions.

We present the design and implementation of EarVoice, a lightweight mobile service that enables hands-free voice assistant activation on commodity earphones. EarVoice comprises two design modules: one for joint speech detection and primary user identification that explores the attributes of the air channel and in-body audio pathway to differentiate between the primary user and others nearby; and another for accurate wakeup word enhancement, which employs a "copy, paste, and adapt" approach to reconstruct the missing high-frequency component in speech recordings. To minimize false positives, enhance agility, and preserve privacy, we deploy EarVoice on a dongle where the proposed signal processing algorithms are streamlined with a gating mechanism to permit only the primary user's speech to enter the pairing device (e.g., a smartphone) for wakeup word recognition, preventing unintended disclosure of ambient conversations. We implemented the dongle on a 4-layer PCB board and conducted extensive experiments with 23 participants in both controlled and uncontrolled scenarios. The experiment results show that EarVoice achieves around 90% wakeup word recognition accuracy in stationary scenarios, which is on par with the high-end, multi-sensor fusion-based Airpods Pro earbud. EarVoice's performance drops to 84% on mobile cases, slightly worse than Airpods (around 90%).

Time-Sensitive Networking (TSN) offers deterministic communication for time-sensitive applications, using Cyclic Queuing and Forwarding (CQF) to manage time-triggered flows (TT flows). Scheduling TT flows is essential for optimizing network resource utilization and scheduling success rates. Existing works prefer heuristic algorithms due to their favorable trade off between computational overhead and performance. However, they overlook two critical factors during design: search space approximation efficiency and the impact of routing policy. In this study, we present H-GATS (Hybrid Genetic Algorithm and Tabu Search) for CQF-based TSN flow routing and scheduling. H-GATS combines the global search of Genetic Algorithms with the local search of Tabu Search, achieving fine-grained search efficiency and reduced execution time in complex networks. Moreover, H-GATS considers the offset and routing of flows, further improving scheduling performance. Compared to GA, Tabu, and JRS-LB, H-GATS is 5.8×, 3.05×, and 1.6× faster, respectively, in achieving the same success rates. Additionally, H-GATS improves the success rate by 5.5%, 9.6%, and 3.9% and enhances the resource utilization rate by 18%, 13.3%, and 3.3% over these baselines.

This paper presents the design, implementation, and evaluation of MagWear, a novel biomagnetism-based system that can accurately and inclusively monitor the heart rate, respiration rate, and blood pressure of users. MagWear's contributions are twofold. First, we build a mathematical model that characterizes the magnetic coupling effect of blood flow under the influence of an external magnetic field. This model uncovers the variations in accuracy when monitoring vital signs among individuals. Second, leveraging insights derived from this mathematical model, we present a software-hardware co-design that effectively handles the impact of human diversity on the performance of vital sign monitoring, pushing this generic solution one big step closer to real adoptions. Following IRB protocols, our extensive experiments involving 30 volunteers demonstrate that MagWear achieves high monitoring accuracy with a mean percentage error (MPE) of 1.55% for heart rate (HR), 1.79% for respiration rate (RR), 3.35% for systolic blood pressure (SBP), and 3.89% for diastolic blood pressure (DBP). MagWear can also be extended to detect anemia and blood oxygen saturation, which is also our ongoing work.

The radio range of backscatter systems continues growing as new wireless communication primitives are continuously invented. Nevertheless, both the bit error rate and the packet loss rate of backscatter signals increase rapidly with the radio range, thereby necessitating the cooperation between the access point and the backscatter tags through a feedback loop. Unfortunately, the low-power nature of backscatter tags limits their ability to demodulate feedback signals from a remote access point and scales down to such circumstances. This paper presents, an ultra-low-power demodulator for long-range LoRa backscatter systems. is based on an observation that a frequency-modulated chirp signal can be transformed into an amplitude-modulated signal using a differential circuit. Moreover, we redesign a LoRa backscatter tag which integrates and a ring oscillator-based modulator. The LoRa backscatter tag enables re-transmission, rate adaption and channel hopping – three PHY-layer operations that are important to channel efficiency yet unavailable on existing long-range backscatter systems. We prototype and the LoRa backscatter tag on two PCB boards and evaluate their performance in different environments. Results show that achieves 3.5–5$\times$gain on the demodulation range, compared with state-of-the-art systems. Our ASIC simulation shows that the power consumption of and the LoRa backscatter tag are around 93.2$\mu W$and 94.7$\mu W$. Code and hardware schematics can be found at: https://github.com/ZangJac/Saiyan.

This paper presents RF-Transformer, a unified backscatter radio hardware abstraction that allows a low-power IoT device to directly communicate with heterogeneous wireless receivers. Unlike existing backscatter systems that are tailored to a specific wireless communication protocol, RF-Transformer provides a programmable interface to the micro-controller, allowing IoT devices to synthesize different types of protocol-compliant backscatter signals in the PHY layer. By leveraging the nonlinear characteristics of the negative impedance, RF-Transformer also achieves a cross-frequency backscatter design that enables IoT devices in harmonic frequency bands to communicate with each other. We implement a PCB prototype of RF-Transformer on 2.4 GHz ISM band and conduct extensive experiments. We leverage the software defined platform USRP to transmit the carrier signal and receive the backscatter signal to verify the efficacy of our design. Our extensive field studies show that RF-Transformer achieves 23.8 Mbps, 247.1 Kbps, 986.5 Kbps, and 27.3 Kbps throughput when generating standard Wi-Fi, ZigBee, Bluetooth, and LoRa signals.

Flow scheduling plays a pivotal role in enabling Time-Sensitive Networking (TSN) applications. Current flow scheduling mainly adopts a centralized scheme, posing challenges in adapting to dynamic network conditions and scaling up for larger networks. To address these challenges, we first thoroughly analyze the flow scheduling problem and find the inherent locality nature of time scheduling tasks. Leveraging this insight, we introduce the first distributed framework for IEEE 802.1Qbv TSN flow scheduling. In this framework, we further propose a multi-agent flow scheduling method by designing Deep Reinforcement Learning (DRL)-based route and time agents for route and time planning tasks. The time agents are deployed on field devices to schedule flows in a distributed way. Evaluations in dynamic scenarios validate the effectiveness and scalability of our proposed method. It enhances the scheduling success rate by 20.31% compared to state-of-the-art methods and achieves substantial cost savings, reducing transmission costs by 410× in large-scale networks. Additionally, we validate our approach on edge devices and a TSN testbed, highlighting its lightweight nature and ease of deployment.

This paper proposes Meta-Speaker, an innovative speaker capable of projecting audible sources into the air with a high level of manipulability. Unlike traditional speakers that emit sound waves in all directions, Meta-Speaker can manipulate the granularity of the audible region, down to a single point, and can manipulate the location of the source. Additionally, the source projected by Meta-Speaker is a physical presence in space, allowing both humans and machines to perceive it with spatial awareness. Meta-Speaker achieves this by leveraging the fact that air is a nonlinear medium, which enables the reproduction of audible sources from ultrasounds. Meta-Speaker comprises two distributed ultrasonic arrays, each transmitting a narrow ultrasonic beam. The audible source can be reproduced at the intersection of the beams. We present a comprehensive profiling of Meta-Speaker to validate the high manipulability it offers. We prototype Meta-Speaker and demonstrate its potential through three applications: anchor-free localization with a median error of 0.13 m, location-aware communication with a throughput of 1.28 Kbps, and acoustic augmented reality where users can perceive source direction with a mean error of 9.8 degrees.

Backscatter is an enabling technology for battery-free sensing in today's Artificial Intelligence of Things (AIOT). Building a backscatter-based sensing system, however, is a daunting task, due to two obstacles: the unaffordable power consumption of the microprocessor and the coexistence with the ambient carrier's traffic. In order to address the above issues, in this paper, we present Leggiero, the first-of-its-kind analog WiFi backscatter with payload transparency. Leveraging a specially designed circuit with a varactor diode, this design avoids using a microprocessor to interface between the radio and the sensor, and directly converts the analog sensor signal into the phase of RF (radio frequency) signal. By carefully designing the reference circuit on the tag and precisely locating the extra long training field (LTF) section of a WiFi packet, Leggiero embeds the analog phase value into the channel state information (CSI). A commodity WiFi receiver without hardware modification can simultaneously decode the WiFi and the sensor data. We implement Leggiero design and evaluate its performance under varied settings. The results show that the power consumption of the Leggiero tag (excluding the power of the peripheral sensor module) is 30μW at a sampling rate of 400Hz, which is 4.8× and 4× lower than the state-of-the-art WiFi backscatter schemes. The uplink throughput of Leggiero is suficient to support a variety of sensing applications, while keeping the WiFi carrier's throughput performance unaffected.

WiFi-based device localization is a key enabling technology for smart applications, which has attracted numerous research studies in the past decade. Most of the existing approaches rely on Line-of-Sight (LoS) signals to work, while a critical problem is often neglected: In the real-world indoor environments, WiFi signals are everywhere, but very few of them are usable for accurate localization. As a result, the localization accuracy in practice is far from being satisfactory. This paper presents Bifrost, a novel hardwaresoftware co-design for accurate indoor localization. The core idea of Bifrost is to reinvent WiFi signals, so as to provide sufficient LoS signals for localization. This is realized by exploiting the dispersion effect of signals emitted by the leaky wave antenna (LWA). We present a low-cost plug-in design of LWA that can generate orthogonal polarized signals: On one hand, LWA disperses signals of different frequencies to different angles, thus providing Angle-of-Arrival (AoA) information for the localized target. On the other hand, the target further leverages the antenna polarization mismatch to distinguish AoAs from different LWAs. In the software layer, fine-grained information in Channel State Information (CSI) is exploited to cope with multipath and noise. We implement Bifrost and evaluate its performance under various settings. The results show that the median localization error of Bifrost is 0.81m, which is 52.35% less than that of SpotFi, a state-of-the-art approach. SpotFi, when combined with Bifrost to work in the realistic settings, can reduce the localization error by 33.54%.

Federated learning (FL) is a machine learning technique that allows for on-site data collection and processing without sacrificing data privacy and transmission. Heterogeneity is a key challenge in federated settings. Recently, cross-technology communication (CTC) has emerged as a solution for Internet of Things (IoT) heterogeneity, enabling direct communication between different wireless devices without the need for hardware modifications or gateway intervention. For example, a sophisticated WiFi device can serve as a central coordinator for other heterogeneous devices, such as LoRa, ZigBee, Bluetooth, and LTE, leading to more efficient and ubiquitous cross-network information exchange. However, heterogeneous wireless technologies present different data transmission rates and computing resources, making it difficult to achieve high accuracy in predictions due to large amounts of multidimensional data, communication delays, transmission latency, limited processing capacity, and data privacy concerns. In this work, we propose an FL framework based on CTC for heterogeneous IoT applications, called FLCTC. To demonstrate the usability of FLCTC, we implemented FLCTC and a specific solution for forest fire prediction. FLCTC was concretely implemented as a federal deep learning based on long and short-term memory and used for forest fire prediction, addressing the challenge of data characterization in heterogeneous IoT networks. FLCTC promises to improve communication efficiency and prediction accuracy. Our platform-based evaluation results show that FLCTC is feasible, with a recall of 96% and an accuracy of 88%, offering valuable insights into the use of FL with CTC for heterogeneous IoT applications.

Time-Slotted Channel Hopping (TSCH) is a popular link-layer pro-tocol defined in the IEEE 802.15.4e standard that improves the reli-ability and throughput of wireless sensor networks by exploiting diversity in both time and frequency. Despite the body of literature proposing several scheduling schemes for TSCH, a gap yet to be filled is the design of an effective way to deal with internal and external interference, which are both known to strongly affect communication performance. In fact, existing works either make use of a fixed schedule (and hence cannot cope with interference), or re-quire extra control traffic (and hence increase energy consumption). In this paper, we present SmarTiSCH, an interference-aware en-gine for IEEE 802.15.4e-based networks that retains the simplicity and energy-efficiency of autonomous scheduling, while increasing the awareness as well as robustness to both internal and external interference. With SmarTiSCH, the nodes in the network infer the presence of interference and react to it without the need of extra control traffic. Specifically, SmarTiSCH enables each node to infer the interference by passively observing existing data exchanges. It then lets a pair of nodes exchange information and mutually agree on a proper strategy to mitigate interference without the need of extra transmissions. We implement SmarTiSCH in Contiki-NG and evaluate its performance on a testbed of 20 off-the-shelf IEEE 802.15.4 devices based on the nRF52840. Our results show that SmarTiSCH increases the reliability of transmissions by up to 2.9 times compared to state-of-the-art approaches in the presence of interference, while even lowering the duty cycle by 54.3%.

This paper presents RF-Transformer, a unified backscatter radio hardware abstraction that allows a low-power IoT device to directly communicate with heterogeneous wireless receivers at the minimum power consumption. Unlike existing backscatter systems that are tailored to a specific wireless communication protocol, RF-Transformer provides a programmable interface to the micro-controller, allowing IoT devices to synthesize different types of protocol-compliant backscatter signals sharing radically different PHY-layer designs. To show the efficacy of our design, we implement a PCB prototype of RF-Transformer on 2.4 GHz ISM band and showcase its capability on generating standard ZigBee, Bluetooth, LoRa, and Wi-Fi 802.11b/g/n/ac packets. Our extensive field studies show that RF-Transformer achieves 23.8 Mbps, 247.1 Kbps, 986.5 Kbps, and 27.3 Kbps throughput when generating standard Wi-Fi, ZigBee, Bluetooth, and LoRa signals while consuming 7.6--74.2X less power than their active counterparts. Our ASIC simulation based on the 65-nm CMOS process shows that the power gain of RF-Transformer can further grow to 92--678X. We further integrate RF-Transformer with pressure sensors and present a case study on detecting foot traffic density in hallways. Our 7-day case studies demonstrate RF-Transformer can reliably transmit sensor data to a commodity gateway by synthesizing LoRa packets on top of Wi-Fi signals. Our experimental results also verify the compatibility of RF-Transformer with commodity receivers. Code and hardware schematics can be found at: https://github.com/LeFsCC/RF-Transformer.

Earables are embedded devices that can be placed in, on, or around the ear to sense human motions and physiological activities over an extended period of time. However, today's earable design principle heavily relies on dedicated sensors (e.g., accelerometer, gyroscope, proximity sensor), which inevitably adds cost, weight, and power consumption to earable devices, constituting a critical bottleneck in their wide adoption. Moreover, the tight coupling of sensors with onboard microcontrollers makes existing earables difficult to program, raising the barrier of entry to earable computing.

Backscatter communication holds potential for ubiquitous and low-cost connectivity among low-power IoT devices. To avoid interference between the carrier signal and the backscatter signal, recent works propose a frequency-shifting technique to separate these two signals in the frequency domain. Such proposals, however, have to occupy the precious wireless spectrum that is already overcrowded, and increase the power, cost, and complexity of the backscatter tag. In this paper, we revisit the classic ON-OFF Keying (OOK) modulation and propose Aloba, a backscatter system that takes the ambient LoRa transmissions as the excitation and piggybacks the in- band OOK modulated signals over the LoRa transmissions. Our design enables the backscatter signal to work in the same frequency band of the carrier signal, meanwhile achieving flexible data rate at different transmission range. The key contributions of Aloba include: i) the design of a low-power backscatter tag that can pick up the ambient LoRa signals from other signals; ii) a novel decoding algorithm to demodulate both the carrier signal and the backscatter signal from their superposition. We further adopt link coding mechanism and interleave operation to enhance the reliability of backscatter signal decoding. We implement Aloba and conduct head-to-head comparison with the state-of-the-art LoRa backscatter system PLoRa in various settings. The experiment results show Aloba can achieve 39.5–199.4 Kbps data rate at various distances, 10.4–$52.4\times $higher than PLoRa.

Cross-Technology Communication (CTC) emerges as a technology to enable direct communication across different wireless technologies. The state of the art on CTC employs physical-level emulation. Due to the protocol incompatibility and the hardware restriction, there are intrinsic emulation errors between the emulated signals and the legitimate signals. Unresolved emulation errors hurt the reliability of CTC and the achievable throughput, but how to improve the reliability of CTC remains a challenging problem. Taking the CTC from WiFi to BLE as an example, this work first presents a comprehensive understanding of the emulation errors. We then propose WEB, a practical CTC approach that can be implemented with commercial devices. The core design of WEB is split encoding: based on the probabilistic distribution of emulation errors, the WiFi sender manipulates its payload to maximize the successful decoding rate at the BLE receiver. We implement WEB and evaluate its performance with extensive experiments. Compared to two existing approaches, WEBee and WIDE, WEB reduces the SER (Symbol Error Rate) by 54.6% and 42.2%, respectively. For the first time in the community, WEB achieves practically effective CTC from WiFi to BLE, with an average throughput of 522.2 Kbps.

Research on cross-technology communication ( CTC ) has made rapid progress in recent years. While the CTC links are complex and dynamic, how to estimate the quality of a CTC link remains an open and challenging problem. Through our observation and study, we find that none of the existing approaches can be applied to estimate the link quality of CTC. Built upon the physical-level emulation, transmission over a CTC link is jointly affected by two factors: the emulation error and the channel distortion. Furthermore, the channel distortion can be modeled and observed through the signal strength and the noise strength. We, in this article, propose a new link metric called C-LQI and a joint link model that simultaneously takes into account the emulation error and the channel distortion in the In-phase and Quadrature ( IQ ) domain. We accurately describe the superimposed impact on the received signal. We further design a lightweight link estimation approach including two different methods to estimate C-LQI and in turn the packet reception rate ( PRR ) over the CTC link. We implement C-LQI and compare it with two representative link estimation approaches. The results demonstrate that C-LQI reduces the relative estimation error by 49.8% and 51.5% compared with s-PRR and EWMA, respectively.

Cross-technology interference is a major threat to the dependability of low-power wireless communications. Due to power and bandwidth asymmetries, technologies such as Wi-Fi tend to dominate the RF channel and unintentionally destroy low-power wireless communications from resource-constrained technologies such as ZigBee, leading to severe coexistence issues. To address these issues, existing schemes make ZigBee nodes individually assess the RF channel's availability or let Wi-Fi appliances blindly reserve the medium for the transmissions of low-power devices. Without a two-way interaction between devices making use of different wireless technologies, these approaches have limited scenarios or achieve inefficient network performance. This paper presents BiCord, a bidirectional coordination scheme in which resource-constrained wireless devices such as ZigBee nodes and powerful Wi-Fi appliances coordinate their activities to increase coexistence and enhance network performance. Specifically, in BiCord, ZigBee nodes directly request channel resources from Wi-Fi devices, who then reserve the channel for ZigBee transmissions on-demand. This interaction continues until the transmission requirement of ZigBee nodes is both fulfilled and understood by Wi-Fi devices. This way, BiCord avoids unnecessary channel allocations, maximizes the availability of the spectrum, and minimizes transmission delays. We evaluate BiCord on off-the-shelf Wi-Fi and ZigBee devices, demonstrating its effectiveness experimentally. Among others, our results show that BiCord increases channel utilization by up to 50.6% and reduces the average transmission delay of ZigBee nodes by 84.2% compared to state-of-the-art approaches.

iBeacon protocol is widely deployed to provide location-based services. By receiving its BLE advertisements, nearby devices can estimate the proximity to the iBeacon or calculate indoor positions. However, the open nature of these advertisements brings vulnerability to impersonation attacks. Such attacks could lead to spam, unreliable positioning, and even security breaches. In this paper, we propose Wi-attack, revealing the feasibility of using WiFi devices to conduct impersonation attacks on iBeacon services. Different from impersonation attacks using BLE compatible hardware, Wi-attack is not restricted by broadcasting intervals and is able to impersonate multiple iBeacons at the same time. Effective attacks can be launched on iBeacon services without modifications to WiFi hardware or firmware. To enable direct communication from WiFi to BLE, we use the digital emulation technique of cross technology communication. To enhance the packet reception along with its stability, we add redundant packets to eliminate cyclic prefix error entirely. The emulation provides an iBeacon packet reception rate up to 66.2%. We conduct attacks on three iBeacon services scenarios, point deployment, multilateration, and fingerprint-based localization. The evaluation results show that Wi-attack can bring an average distance error of more than 20 meters on fingerprint-based localization using only 3 APs.

Wireless sensing has great significance in Internet of Things (IoT) applications and has attracted substantial research interests in academia. In this study, we propose Palantir, a first-of-its-kind long-range sensing system based on the LoRa backscatter technology. By utilizing the ON-OFF-Keying modulated backscatter signals, Palantir can perform fine-grained long-range cyclist sensing. Our findings show that sensing is more susceptible to channel quality than communication. Hence, the design of Palantir particularly addresses the critical challenges of signal processing, such as amplitude instability, frequency offset, clock drift, spectrum leakage, and multiplicative noise. We implement Palantir and evaluate its performance by conducting comprehensive benchmark experiments. A prototype is also built and a case study of respiration monitoring in the real world is implemented. Results demonstrate that Palantir can perform accurate sensing at a range up to 100 m, which is twice that of state-of-the-art approaches. The median deviation of the detected motion period is as low as 0.2%.

Cross-Technology Communication (CTC) is an emerging technique that enables direct communication across different wireless technologies. The state-of-the-art works in this area propose physical-level CTC, in which the transmitters emulate signals that follow the receiver's standard. Physical-level CTC means considerable processing complexity at the transmitter, which does not apply to the communication from a low-end transmitter to a high-end receiver. This article proposes LEGO-Fi, which supports the CTC from ZigBee to WiFi and Bluetooth to WiFi. LEGO-Fi is a transmitter-transparent CTC technique, which leaves the processing complexity solely at the receiver side and therefore, makes a critical advance toward bidirectional high-throughput CTC. The key technique inside is cross-demapping, which stems from two key technical insights: 1) a ZigBee/Bluetooth packet leaves distinguishable features when passing the WiFi modules and 2) compared to ZigBee's/Bluetooth's simple encoding and modulation schemes, the rich processing capacity of WiFi offers extra flexibility to process a ZigBee/Bluetooth packet. The evaluation results show that LEGO-Fi achieves a throughput of 213.6 Kb/s in practice, which is, respectively, 13000×, 1200×, and 7.5× faster than FreeBee, ZigFi, and SymBee, the three existing ZigBee-to-WiFi CTC approaches. For the CTC from Bluetooth to WiFi, LEGO-Fi achieves a throughput of 904.1 Kb/s.

Cross-Technology Communication (CTC) is an emerging technique that enables direct communication across different wireless technologies. Recent works achieve physical-level CTC by emulating the standard time-domain waveform of the receiver. This method faces the challenges of inherent unreliability due to the imperfect emulation. Different from analog emulation, we propose a novel concept named digital emulation, which stems from the following insight: The receiver relies on phase shift rather than the phase itself to decode signals. Instead of emulating the original time-domain waveform, the sender emulates the phase shift associated with the desired signals. Clearly there are multiple different phase sequences that correspond to the same signs of phase shifts. Digital emulation has flexibility in setting the phase values in the emulated signals, which is effective in reducing emulation errors and enhancing the reliability of CTC. The key point of digital emulation is generic and applicable to a set of CTCs, where the transmitter has a wider bandwidth for emulation and the receiver decoding is based on the phase shift. In this paper, we implement our proposal as WIDE, a physical-level CTC via digital emulation from WiFi to ZigBee. We conduct extensive experiments to evaluate the performance of WIDE. The results show that WIDE significantly improves the Packet Reception Ratio (PRR) from 41.7% to 86.2%, which is 2× of WEBee's, an existing representative physical-level CTC.

Research on Cross-technology communication (CTC) has made rapid progress in recent years, but how to estimate the quality of a CTC link remains an open and challenging problem. Through our observation and study, we find that none of the existing approaches can be applied to estimate the link quality of CTC. Built upon the physical-level emulation, transmission over a CTC link is jointly affected by two factors: the emulation error and the channel distortion. We in this paper propose a new link metric called C-LQI and a joint link model that simultaneously takes into account the emulation error and the channel distortion in the process of CTC. We further design a light-weight link estimation approach to estimate C-LQI and in turn the PRR over the CTC link. We implement C-LQI and compare it with two representative link estimation approaches. The results demonstrate that C-LQI reduces the relative error of link estimation respectively by 46% and 53% and saves the communication cost by 90%.

Opportunistic forwarding seizes early forwarding opportunities in duty-cycled networks to reduce delay and energy consumption. But increasingly serious Cross-Technology Interference (CTI) significantly counteracts the benefits of opportunistic forwarding. Existing solutions try to reserve the channel for low-power networks by implicit avoidance or explicit coordination but ignore the potential of high-power CTI's superior capability. In this paper, we propose a new paradigm for low-power opportunistic forwarding in CTI environments. Instead of keeping high-power CTI devices silent, we directly involve them into the forwarding, as cross-technology forwarders. We design Portal to solve the challenges of realizing cross-technology opportunistic forwarding. To be transparent to the low-power networks, Portal adopts cross-technology rebroadcasting to enable the fast overhearing and forwarding of cross-technology data. To maximize the performance gain of using heterogeneous forwarders while minimizing the influence on legacy high-power traffic, we propose a post-forwarding forwarder selection and a traffic scheduling method. We also propose a feature-based ACK recognition method and a jamming-based ACK replying mechanism to forward the unreliable ACKs from asymmetric regions. Extensive experiments demonstrate that Portal not only avoids the CTI but also breaks through the existing performance limit.

Backscatter communication holds potential for ubiquitous and low-cost connectivity among low-power IoT devices. To avoid interference between the carrier signal and the backscatter signal, recent works propose a frequency-shifting technique to separate these two signals in the frequency domain. Such proposals, however, have to occupy the precious wireless spectrum that is already overcrowded, and increase the power, cost, and complexity of the backscatter tag. In this paper, we revisit the classic ON-OFF Keying (OOK) modulation and propose Aloba, a backscatter system that takes the ambient LoRa transmissions as the excitation and piggybacks the in-band OOK modulated signals over the LoRa transmissions. Our design enables the backsactter signal to work in the same frequency band of the carrier signal, meanwhile achieving good tradeoff between transmission range and link throughput. The key contributions of Aloba include: i) the design of a low-power backscatter tag that can pick up the ambient LoRa signals from other signals; ii) a novel decoding algorithm to demodulate both the carrier signal and the backscatter signal from their superposition. The design of Aloba completely unleashes the backscatter tag's ability in OOK modulation and achieves flexible data rate at different transmission range. We implement Aloba and conduct head-to-head comparison with the state-of-the-art LoRa backscatter system PLoRa in various settings. The experiment results show Aloba can achieve 39.5--199.4 Kbps data rate at various distances, 10.4--52.4X higher than PLoRa.

The proliferation of IoT applications brings the demand of ubiquitous connections among heterogeneous wireless devices. Cross-Technology Communication (CTC) is a significant technique to directly exchange data among heterogeneous devices that follow different standards. By exploiting a side-channel like frequency, amplitude, or temporal modulation, the existing works enable CTC but have limited performance under channel noise. In this article, we propose WiZig, a novel CTC technique from WiFi to ZigBee that employs modulations in both the amplitude and temporal dimensions to optimize the throughput over a noisy channel. We establish a theoretical model of the energy communication channel to clearly understand the channel capacity. We then devise an online rate adaptation algorithm to adjust the modulation strategy according to the channel condition. Based on the theoretical model, WiZig controls the number of encoded energy amplitudes and the length of a receiving window, so as to optimize the CTC throughput. We implement a prototype of WiZig on a software radio platform and a commercial ZigBee device. The evaluation shows that WiZig achieves a throughput of 153.85bps with less than 1% symbol error rate in a real environment.

Cross-technology communication (CTC) is a technique that enables direct communication among different wireless technologies. Recent works in this area have made substantial progress, but CTC from ZigBee to WiFi remains an open problem. In this paper, we propose ZigFi, a novel CTC framework that enables communication from ZigBee to WiFi. ZigFi carefully overlaps ZigBee packets with WiFi packets. Through experiments we show that Channel State Information (CSI) of the overlapped packets can be used to convey data from ZigBee to WiFi. Based on this finding, we propose a receiver-initiated protocol and translate the decoding problem into a problem of CSI classification with Support Vector Machine. We further build a generic model through experiments, which describes the relationship between the Signal to Interference and Noise Ratio (SINR) and the symbol error rate (SER). Moreover, we extend ZigFi to multiple-to-one concurrent transmissions. We implement ZigFi on commercial-off-the-shelf WiFi and ZigBee devices. We evaluate the performance of ZigFi under different experimental settings. The results demonstrate that ZigFi achieves a throughput of 215.9bps, which is 18X faster than the state of the arts.

Cross-Technology Communication (CTC) is an emerging technique that enables direct communication across different wireless technologies. The state-of-the-art works in this area propose physical-level CTC, in which the transmitters emulate signals that follow the receiver's standard. Physical-level CTC means considerable processing complexity at the transmitter, which doesn't apply to the communication from a low-end transmitter to a high-end receiver, e.g. from ZigBee to WiFi. This paper presents transmitter-transparent cross-technology communication, which leaves the processing complexity solely at the receiver side and therefore makes a critical advance toward bidirectional high-throughput CTC. We implement our proposal as LEGO-Fi, the communication from ZigBee to WiFi. The key technique inside is cross-demapping, which stems from two key technical insights: (1) A ZigBee packet leaves distinguishable features when passing the WiFi modules. (2) Compared to ZigBee's simple encoding and modulation schemes, the rich processing capacity of WiFi offers extra flexibility to process a ZigBee packet. The evaluation results show that LEGO-Fi achieves a throughput of 213.6Kbps, which is respectively 13000× and 1200× faster than FreeBee and ZigFi, the two existing ZigBee-to-WiFi CTC approaches.

Cross-Technology Communication (CTC) is an emerging technique that enables direct communication across different wireless technologies. Recent works achieve physical-level CTC by emulating the standard time-domain waveform of the receiver. This method faces the challenges of inherent unreliability due to the imperfect emulation. Different from analog emulation, we propose a novel concept named digital emulation, which stems from the following insight: The receiver relies on the phase shift to decode symbols rather than the shape of analog time-domain waveform. There are lots of phase sequences which satisfy the requirement of phase shift. The distortions of these phase sequences after WiFi emulation are different. We have the opportunity to select an appropriate phase sequence with the relatively small emulation errors to achieve a reliable CTC. The key point of digital emulation is generic and applicable to a set of CTCs, where the transmitter has a wider bandwidth for emulation and the receiver decoding is based on the phase shift. In this paper, we implement our proposal as WIDE, a physical-level CTC via digital emulation from WiFi to ZigBee. We conduct extensive experiments to evaluate the performance of WIDE. The results show that WIDE significantly improves the Packet Reception Ratio (PRR) from 41.7% to 86.2%, which is 2X of WEBee's, an existing representative physical-level CTC.

Cross-Technology Communication (CTC) is an emerging technology to support direct communication between wireless devices that follow different standards. In spite of the many different proposals from the community to enable CTC, the performance aspect of CTC is an equally important problem but has seldom been studied before. We find this problem is extremely challenging, due to the following reasons: on one hand, a link for CTC is essentially different from a conventional wireless link. The conventional link indicators like RSSI (received signal strength indicator) and SNR (signal to noise ratio) cannot be used to directly characterize a CTC link. On the other hand, the indirect indicators like PER (packet error rate), which is adopted by many existing CTC proposals, cannot capture the short-term link behavior. As a result, the existing CTC proposals fail to keep reliable performance under dynamic channel conditions. In order to address the above challenge, we in this paper propose AdaComm, a generic framework to achieve self-adaptive CTC in dynamic channels. Instead of reactively adjusting the CTC sender, AdaComm adopts online learning mechanism to adaptively adjust the decoding model at the CTC receiver. The self-adaptive decoding model automatically learns the effective features directly from the raw received signals that are embedded with the current channel state. With the lossless channel information, AdaComm further adopts the fine tuning and full training modes to cope with the continuous and abrupt channel dynamics. We implement AdaComm and integrate it with two existing CTC approaches that respectively employ CSI (channel state information) and RSSI as the information carrier. The evaluation results demonstrate that AdaComm can significantly reduce the SER (symbol error rate) by 72.9% and 49.2%, respectively, compared with the existing approaches.

Cross- Technology Communication (CTC) is an emerging technique to enable the direct communication among different wireless technologies. A main category of the existing proposals on CTC propose to modulate packets at the sender side, and demodulate them into 1 and 0 bits at the receiver side. The performance of those proposals is likely to degrade in a densely coexisting environment. Solely judged according to the received signal strength, a symbol 0 that is modulated as packet absence is generally indistinguishable from dynamic interference. In this paper, we propose StripComm, interference-resilient CTC in coexisting environments. A sender in StripComm adopts an interference-resilient coding scheme that contains both presence and absence of packets in one symbol. The receiver strips the interference from the interested signal by exploiting the self-similarity of StripComm signals. We prototype StripComm with commercial WiFi, ZigBee devices and a software radio platform. The theoretical and experimental evaluation demonstrate that StripComm offers a data rate up to 1.1K bps with a SER (Symbol Error Rate) lower than 0.01 and a data rate of 0.89K bps even against strong interference.

Cross-technology communication (CTC) is a technique that enables direct communication among different wireless technologies. Recent works in this area have made positive progress, but high-throughput CTC from ZigBee to WiFi remains an open problem. In this paper, we propose ZigFi, a novel CTC framework that enables direct communication from ZigBee to WiFi. Without impacting the ongoing WiFi transmissions, ZigFi carefully overlaps ZigBee packets with WiFi packets. Through experiments we show that Channel State Information (CSI) of the overlapped packets can be used to convey data from ZigBee to WiFi. Based on this finding, we propose a receiver-initiated protocol and translate the decoding problem into a problem of CSI classification with Support Vector Machine. We further build a generic model through experiments, which describes the relationship between the Signal to Interference and Noise Ratio (SINR) and the symbol error rate (SER). We implement ZigFi on commercial-off-the-shelf WiFi and ZigBee devices. We evaluate the performance of ZigFi under different experimental settings. The results demonstrate that ZigFi achieves a throughput of 215.9bps, which is 18X faster than the state-of-the-art.

The development of Internet-of-Things (IoT) technologies in recent years brings us unprecedented opportunities for innovations in the power industry. This demo abstract introduces our research and practice with Pavatar - IoT for the power industry. Pavatar includes a series of system deployments in the core sections of Global Energy Internet (GEI), for the purposes of automatic surveillance and remote diagnosis of ultra-high-voltage converter stations (UHVCSs). Pavatar incorporates technologies like lower-power or battery-free sensing, cross-technology communication, edge computing, machine learning, and enhances the user experience with 3D virtual reality. The deployed system significantly reduces the manpower cost and enhances the operational efficiency of the UHVCS.

The proliferation of loT applications drives the need of ubiquitous connections among heterogeneous wireless devices. Cross-Technology Communication (CTC) is a significant technique to directly exchange information among heterogeneous devices that follow different standards. By exploiting a side-channel like frequency, amplitude or temporal modulation, the existing works enable CTC but have limited performance under channel noise. In this paper, we propose WiZig, a novel CTC technique that employs modulation techniques in both the amplitude and temporal dimensions to optimize the throughput over a noisy channel. We establish a theoretical model of the energy communication channel to clearly understand the channel capacity. We then devise an online rate adaptation algorithm to adjust the modulation strategy according to the channel condition. Based on the theoretical model, WiZig can accurately control the number of encoded energy amplitudes and the length of a receiving window, so as to optimize the CTC throughput. We implement a prototype of WiZig on a software radio platform and a commercial ZigBee device. The evaluation show that WiZig achieves a throughput of 153.85 bps with less than 1 % symbol error rate in a real environment. The results demonstrate that WiZig realizes efficient and reliable CTC under varied channel conditions.

The application of Wireless Sensor Networks (WSNs) often falls into unexpected poor performance conditions due to many factors such as complex network interactions, software bugs and incorrect configurations. Diagnosing such a network is challenging since it is difficult to obtain information from the network due to factors including (1) non-deterministic network interactions among motes, (2) difficulties in reconstructing the status of each individual mote, and (3) unavailability of the real environment information. To address these problems, we propose a diagnosis tool called ALog which analyzes the local logs and the source code to infer what happens in network. Based on the analysis, we further derive the states and possible problems accordingly. We implement ALog and evaluate its efficiency with two real case studies. The results demonstrate that ALog is accurate and applicable for diagnosing real sensor networks.