High-level synthesis (HLS) promises to increase the design and verification productivity for digital hardware systems. However, the industry still predominantly uses more time-consuming manual register-transfer level techniques instead of HLS. To accelerate the adoption of HLS, it is vital to explore if it is possible to achieve competitive results with this method. To that end, this paper demonstrates an HLS implementation of the well-known MUSIC algorithm for estimating the direction of arrival of a radio signal. We use as a receiver a four-antenna uniform linear array with one signal source and a resolution of one degree. For the computationally heavy eigenvalue decomposition within MUSIC, we employ the iterative Jacobi algorithm. We target two different Virtex FPGAs for synthesis and obtain results faring well in comparison to the previous literature, with$5.0\ \mu \mathrm{s}$microseconds latency, high accuracy, and low resource consumption. The results show that HLS is suitable for implementing these kinds of algorithms on FPGA.

In this article, we address the timely topic of cellular bistatic simultaneous localization and mapping (SLAM) with specific focus on end-to-end processing solutions, from raw I/Q samples, via channel parameter estimation to user equipment (UE) and landmark location information in millimeter-wave (mmWave) networks, with minimal prior knowledge. Firstly, we propose a new multipath channel parameter estimation solution that operates directly with beam reference signal received power (BRSRP) measurements, alleviating the need to know the true antenna beampatterns or the underlying beamforming weights. Additionally, the method has built-in robustness against unavoidable antenna sidelobes. Secondly, we propose new snapshot SLAM algorithms that have increased robustness and identifiability compared to prior art, in practical built environments with complex clutter and multi-bounce propagation scenarios, and do not rely on any a priori motion model. The performance of the proposed methods is assessed at the 60GHz mmWave band, via both realistic ray-tracing evaluations as well as true experimental measurements, in an indoor environment. A wide set of offered results demonstrate the improved performance, compared to the relevant prior art, in terms of the channel parameter estimation as well as the end-to-end SLAM performance. Finally, the article provides the measured 60GHz data openly available for the research community, facilitating results reproducibility as well as further algorithm development.

Since the beginning of the fifth generation (5G) standardization process, positioning has been considered as a key element in future cellular networks. In order to perform accurate positioning, solutions for estimating and processing location-related measurements such as direction of arrival (DoA) and time of arrival (ToA) for various use-cases need to be developed. In this paper, building on the existing 5G new radio (NR) specifications and millimeter wave frequencies, we propose a novel estimation and tracking solution of the DoA and ToA such that only analog/radio frequency (RF) beamforming-based observations are utilized. In addition to the proposed extended Kalman filter (EKF)-based estimation and tracking approach, we derive Cramér-Rao lower bounds (CRLBs) for the considered RF multi-beam system, and propose an information-based criterion for selecting the necessary beams for the estimation process in order to provide highly accurate performance with feasible computational complexity. The performance of the proposed method is evaluated using extensive ray-tracing simulations and numerical evaluations, and the results are compared with other estimation and beam-selection approaches. Based on the obtained results, beam-selection at the receiver can have a significant impact on the DoA and ToA estimation performance as well as on the subsequent positioning accuracy. Finally, we demonstrate the highly accurate performance of the methods when extended to joint multi-receiver-based device positioning and clock synchronization.

Integrated communications, localization and sensing is one of the most addressed technologies considered for future mobile communications systems. In this context, a user equipment (UE)-centric mobile radar has been proposed to introduce improved situational awareness, and consequently potential improvement in network performance. In this paper, we derive an extended Kalman probability hypothesis density (EK-PHD) filter with a novel feature model, for a mobile radar based environment mapping, where range-angle detections are used to track map objects over time for dynamic map construction. In order to evaluate the performance of the proposed filtering approach, we employ a realistic ray-tracing-based simulation setup, which models the full transmission chain from the transmitted IQ-samples to mapping results. Besides this, a simplified measurement model considering solely single-bounce specular reflections is exploited for providing further insight into the filter performance. The obtained results show that the proposed EK-PHD filter is able to provide high-quality mapping results, reaching around 10 cm landmark estimation accuracy in the considered millimeter wave simulation setup.

The millimeter wave (mmWave) device-to-device air interface not only supports a direct wireless connectivity among devices, but it also offers an improved beamforming capability to obtain the direction information among the vehicles and devices for positioning. Both features serve as the key physical layer components for communications and positioning in the industrial Internet of things (IIoT) systems. Exploiting both accurate beamforming and wide bandwidth in a mmWave network, high-accuracy positioning is achievable, which can be then facilitated for location-aware communications, for instance. However, the uncertainty of anchors' locations in the industrial environment highly degrades the achievable positioning accuracy if left without proper consideration. In order to resolve such challenge, this paper presents a cooperative positioning system (CPS), where the locations of all the vehicles and anchors can be jointly estimated based on acquired location-related measurements (LRMs). Furthermore, the positioning performance is evaluated under random trajectories and different geometric relationships between the vehicles and the anchors. We show that, the proposed positioning solution is capable of resolving the aforementioned challenge by simultaneously tracking the mobile vehicles while mapping the locations of the static anchors. Utilizing the LRMs from both time and angular domains, the achieved positioning accuracy in both 2D and vertical plane is demonstrated based on extensive numerical simulations. Last but not least, the impact of different numbers of the mobile vehicles on the overall positioning performance is also investigated.

In this paper, we exploit the 3D-beamforming features of multiantenna equipment employed in fifth generation (5G) networks, operating in the millimeter wave (mmW) band, for accurate positioning and tracking of users. We consider sequential estimation of users' positions, and propose a two-stage extended Kalman filter (EKF) that is based on reference signal received power (RSRP) measurements. In particular, beamformed downlink (DL) reference signals (RSs) are transmitted by multiple base stations (BSs) and measured by user equipments (UEs) employing receive beamforming. The so-obtained beam-RSRP (BRSRP) measurements are reported to the BSs where the corresponding directions of departure (DoDs) are sequentially estimated by a novel EKF. Such angle estimates from multiple BSs are subsequently fused on a central entity into 3D position estimates of UEs by means of another (second-stage) EKF. The proposed positioning scheme is scalable since the computational burden is shared among different network entities, namely transmission/reception points (TRPs) and 5G-NR Node B (gNB), and may be accomplished with the signalling currently specified for 5G. We assess the performance of the proposed algorithm on a realistic outdoor 5G deployment with a detailed ray tracing propagation model based on the METIS Madrid map. Numerical results with a system operating at 39 GHz show that sub-meter 3D positioning accuracy is achievable in future mmW 5G networks.

This paper considers direction-finding in millimeter wave (mmW) fifth generation (5G) networks by means of beam-based downlink (DL) reference signal received power (RSRP) measurements and subsequent reporting. In particular, we propose two methods that allow user equipments (UEs) to select, in an independent and dynamic manner, the most-relevant beam-RSRP (BRSRP) measurements as a trade-off between angle-related information and load of the feedback channel. A likelihood ratio (LR)-test is derived in which the hypothesis for “noise-only” BRSRP measurement is compared to that of “reference signal (RS)-plus-noise” observations, under a given significance level. A power threshold based method is also proposed in which the BRSRP measurements are compared to a threshold proportional to the noise power. Such a noise variance is estimated at each UE independently. The performance of the proposed beam selection schemes is assessed by means of an extended Kalman filter (EKF) tracking the direction of departure (DoD) of the line-of-sight (LoS) path between base stations (BSs) and a UE. Extensive numerical results are provided on a realistic mmW 5G outdoor deployment scenario operating at 39 GHz and with a ray-tracing propagation model based on the METIS Madrid grid.