In an azimuth multichannel synthetic aperture radar (SAR) system operating in sliding spotlight mode or Terrain Observation by Progressive Scans (TOPS) mode, due to the varying Doppler centroid and the greater processed Doppler bandwidth, the conventional channel phase error estimation algorithms that tailored to stripmap mode will fail and unable to be directly employed. To address these issues, a deramping-based method is proposed in this letter, which extends the conventional methods to sliding spotlight and TOPS cases. By multiplying the signals of each channel with the corresponding deramp phase, the problem of varying Doppler centroid is solved, and its resulting greater Doppler bandwidth is reduced. Therefore, the spectral properties of the signals are the same as those in the stripmap case, and the conventional channel phase error estimation methods can be applied subsequently. Estimation and imaging results of the simulation data and the real data of GaoFen-3 (GF-3) operating in dual-channel sliding spotlight mode demonstrate the effectiveness of the proposed method.

Multichannel SAR system operating in the sliding spotlight mode has the capacity of imaging with very high resolution as requested by future spaceborne synthetic aperture radar (SAR) mission; hence, it has been attracted more and more attention in the SAR community. In a multichannel sliding spotlight SAR system with$N$channels, the overall Doppler bandwidth of the data acquired by each channel is greater than$N \cdot \text {PRF}$; thus, the preprocessing algorithms (channel mismatch calibration and signal reconstruction) are no more available. To address this issue, a full-aperture imaging method for azimuth multichannel sliding spotlight mode is proposed in this article. First, the raw data of each channel need to be preprocessed based on a deramping operation, which can obtain an unambiguous Doppler spectrum. Afterward, the algorithm proposed for single-channel sliding spotlight mode can be performed. Finally, to avoid possible back-folded SAR images, postprocessing after focusing is demanded in some cases. The imaging results of the data acquired by GaoFen-3 (GF-3) are given for the first time in this article, which proves the effectiveness of the proposed imaging method and demonstrates the capacity of high-resolution wide-swath imaging of the multichannel sliding spotlight mode.

One of the challenges of the low-frequency spaceborne synthetic aperture radar (SAR) is that propagation through the ionosphere will introduce nonnegligible errors in the final SAR product. In the low-frequency bistatic SAR (BiSAR) system, the ionosphere will degrade the imaging performance and cause nonnegligible phase errors in the single-pass SAR interferometry application, which results in undesired errors of digital elevation model (DEM). In this article, a method that embedded into the focusing procedure is proposed, which aims to estimate and remove ionospheric effects on L-band spaceborne BiSAR system. First, the impacts of ionospheric effects on the BiSAR system are demonstrated, including the deterioration of imaging performance and the geometric distortion. Then, a method is proposed to correct ionospheric effects. Afterward, the simulations, including point targets and distributed targets, are carried out to verify the effectiveness of the proposed method. The imaging results and the DEM reconstruction results show that the proposed method can effectively estimate and remove ionospheric effects on spaceborne BiSAR systems.

The ionosphere is a significant source of the phase dispersion on the low frequency radar signal for spaceborne synthesis aperture radar (SAR). LuTan-1 (LT-1) is an innovative spaceborne bistatic SAR (BiSAR) operated in L-band, which will be launch in 2021. Studying the impacts of ionospheric effects on spaceborne single-pass imaging and interferometry is a necessary work to support the ground processing system of LT-1. In this paper, The geometric distortions caused by the ionosphere, including the offsets of the SAR image and Digital Elevation Model, are analyzed firstly. Then the deterioration of the imaging performance caused by the quadratic phase error and the cubical phase error is analyzed, and simulation results of the point target are given to verify. Finally, a framework of ionospheric effects correction for BiSAR is proposed.

The bistatic synthetic aperture radar (BiSAR) plays an important role in remote sensing. However, the deviation between the two oscillators in BiSAR systems will cause a residual modulation of the echo signal. Therefore, the phase synchronization is an important issue that must be addressed in the BiSAR system. An advanced noninterrupted phase synchronization scheme is used for LuTan-1. The synchronization pulses are exchanged immediately after the ending time of the radar echo receiving window and before the starting time of the next pulse repetition interval, which will not interrupt the normal SAR operation. In order to evaluate the accuracy of the phase synchronization scheme, the model of phase synchronization is introduced at first. The hardware design and processing flow of LuTan-1 are introduced in detail. An innovative internal calibration strategy is also described. Then, the test data acquired by the ground validation system are analyzed to verify the effectiveness of the phase synchronization scheme. The signal-to-noise ratio (SNR) and the synchronization rate are the two most important factors to influence the accuracy in phase synchronization. The conclusions have guiding significance for the synchronization module design of LuTan-1 and the future BiSAR system.

This paper demonstrates the first experiment of Gaofen-3 (GF-3) satellite operated in dual-channel sliding spotlight mode. First, the raw data of two channels need to be preprocessed, including channel error correction and signal reconstruction, so that it can be focused by the subsequent conventional single-channel sliding spotlight mode imaging methods. After imaging processing, to avoid the possible back-folded SAR image, it is necessary to carry out postprocessing step. The imaging result of the data acquired by GF-3 is first given in this paper, it proves the capacity of achieving high-resolution wide-swath of multi-channel sliding spotlight mode, and the effectiveness of the processing method.

For ultra-high resolution spaceborne spotlight synthetic aperture radar data processing, an imaging algorithm is proposed in this paper, which takes into account the variation of the effective velocity caused by the curved orbit. First, an airborne SAR one-step motion compensation (MOCO) method is performed to compensate for the errors introduced by the curved orbit. Then, an azimuth decompression filter is utilized to separate the rang-focusing and the azimuth-focusing after a modified Stolt interpolation. Finally, a residual range cell migration correction (RCMC) and the azimuth compression are implemented successively, considering the range dependence of the effective velocity. Simulation results confirm the effectiveness of the proposed algorithm.