Future Internet-of-Things networks are envisioned to use small and cheap sensor nodes with extremely low power consumption to avoid the extensive use of batteries. To provide connectivity to a massive number of these nodes, backscatter communication (BC) is emerging as an energy- and cost-efficient technology exploiting the reflection of radio frequency signals. However, challenges such as round-trip path loss and direct link interference (DLI) between the carrier emitter and the reader limit its performance. To tackle these limitations, this paper proposes a joint access point role selection and a novel beamforming technique for bistatic BC in a distributed multiple-input multiple-output setup. The proposed approach boosts the received backscattered energy while effectively mitigating DLI, thereby reducing the error probability. We also propose a channel estimation method tailored to operate under DLI conditions and propose a mismatch detector using estimated channel coefficients. Furthermore, we derive a closed-form expression for the probability of error for the detectors and model the quantization noise caused by DLI. Finally, comprehensive simulation results show that the proposed method with 1-bit analog-to-digital converters (ADCs) effectively mitigates DLI, reduces the quantization noise, and enhances backscattered signal energy, achieving performance comparable to the benchmark scenario with 8-bit ADCs.

Broad beam beamforming (BF) design in multiple-input multiple-output (MIMO) can be convenient for initial access, synchronization, and sensing capabilities in cellular networks by avoiding overheads of sweeping methods while making efficient use of resources. Phase-only BF is key for maximizing power efficiency across antennas. A successful method to produce broad beams is the phase-only dual-polarization BF (DPBF). However, its efficiency has not been proved in non-line-of-sight (NLoS). Therefore, this paper contributes by evaluating DPBF in collocated and distributed MIMO configurations under both line-of-sight (LoS) and NLoS channel conditions. We model the reflection coefficients for different materials in NLoS conditions and propose the use of orthogonal space-time block code to improve the coverage compared to the DPBF in collocated MIMO (C-MIMO). We further propose a DPBF method for distributed MIMO and show that it achieves better coverage than C-MIMO with DPBF.

Backscatter communication (BC) has emerged as a key technology to satisfy the increasing need for low-cost and green Internet-of-Things (IoT) connectivity, especially in large-scale deployments. Unlike the monostatic BC (MoBC), the bistatic BC (BiBC) has the possibility to decrease the round-trip path loss by having the carrier emitter (CE) and the reader in different locations. Therefore, this work investigates the BiBC in the context of cell-free multiple-input multiple-output (MIMO) networks by exploring the optimal selection of CE and reader among all access points, leveraging prior knowledge about the area where the backscatter device (BD) is located. First, a maximum a posteriori probability (MAP) detector to decode the BD information bits is derived. Then, the exact probability of error for this detector is obtained. In addition, an algorithm to select the best CE-reader pair for serving the specified area is proposed. Finally, simulation results show that the error performance of the BC is improved by the proposed algorithm compared to the benchmark scenario.

Backscatter communication (BC) is a promising technique for future Internet-of-Things (IoT) owing to its low complexity, low cost, and potential for energy-efficient operation in sensor networks. There are several network infrastructure setups that can be used for BC with IoT nodes. One of them is the bistatic setup where typically there is a need for high dynamic range and high-resolution analog-to-digital converters at the reader. In this paper, we investigate a bistatic BC setup with multiple antennas. We propose a novel transmission scheme, which includes a protocol for channel estimation at the carrier emitter (CE) as well as a transmit beamformer construction that suppresses the direct link interference between the two ends of a bistatic link (namely CE and reader), and increases the detection performance of the backscatter device (BD) symbol. Further, we derive a generalized log-likelihood ratio test (GLRT) to detect the symbol/presence of the BD. We also provide an iterative algorithm to estimate the unknown parameters in the GLRT. Finally, simulation results show that the required dynamic range of the system is significantly decreased, and the detection performance of the BD symbol is increased, by the proposed algorithm compared to a system not using beamforming at the CE.

Backscatter communication (BSC) is a promising solution for Internet-of-Things (IoT) connections due to its low-complexity, low-cost, and energy-efficient solution for sensors. There are several network infrastructure setups that can be used for BSC with IoT nodes/passive devices. One of them is a bistatic setup where there is a need for high dynamic range and high-resolution analog-to-digital converters at the reader side. In this paper, we investigate a bistatic BSC setup with multiple antennas. We propose a novel algorithm to suppress direct link interference between the carrier emitter (CE) and the reader using beamforming into the nullspace of the CE-reader direct link to decrease the dynamic range of the system and increase the detection performance of the backscatter device (BSD). Further, we derive a Neyman-Pearson (NP) test and an exact closed-form expression for its performance in the detection of the BSD. Finally, simulation results show that the dynamic range of the system is significantly decreased and the detection performance of the BSD is increased by the proposed algorithm compared to a system not using beamforming in the CE, which could then be used in a host of different practical fields such as agriculture, transportation, factories, hospitals, smart cities, and smart homes.