The Internet's success arose from classical layering: protocols like TCP and Ethernet can be independently understood, changed, debugged, verified, and offloaded to hardware using a clean service interface between layers. To accrue the same benefits at a finer grain, we suggest sublayering, i.e., layering recursively within each layer. We show that the data link and routing layers have natural sublayers. However, while TCP intuitively decomposes into sub-functions (connection management, reliable delivery, congestion control) common state variables like sequence numbers and window sizes entangle these functions, making sublayering difficult. We propose an alternate sublayered TCP with equivalent functionality which enables easily changing congestion control and connection management. We also argue that sublayering can help create robust and verified Internet protocol implementations akin to seL4 for Operating Systems. To this end, we describe early experiments with a verified sublayered implementation of a simple bit-stuffing protocol using Coq, and a verified monolithic implementation of a lightweight TCP using Dafny. We end with a set of challenges for sublayered protocols.

Recently, neural networks have improved MinSum message-passing decoders for low-density parity-check (LDPC) codes by multiplying or adding weights to the messages, where the weights are determined by a neural network. The neural network complexity to determine distinct weights for each edge is high, often limiting the application to relatively short LDPC codes. Furthermore, storing separate weights for every edge and every iteration can be a burden for hardware implementations. To reduce neural network complexity and storage requirements, this paper proposes a family of weight-sharing schemes that use the same weight for edges that have the same check node degree and/or variable node degree. Our simulation results show that node-degree-based weight-sharing can deliver the same performance requiring distinct weights for each node. This paper also combines these degree-specific neural weights with a reconstruction-computation-quantization (RCQ) decoder to produce a weighted RCQ (W-RCQ) decoder. The W-RCQ decoder with node-degree-based weight sharing has a reduced hardware requirement compared with the original RCQ decoder. As an additional contribution, this paper identifies and resolves a gradient explosion issue that can arise when training neural LDPC decoders.

This paper uses the reconstruction-computation-quantization (RCQ)paradigm to decode low-density parity-check (LDPC) codes. RCQ facilitates dynamic non-uniform quantization to achieve good frame error rate (FER) performance with very low message precision. For message-passing according to a flooding schedule, the RCQ parameters are designed by discrete density evolution. Simulation results on an IEEE 802.11 LDPC code show that for 4-bit messages, a flooding Min Sum RCQ decoder outperforms table-lookup approaches such as information bottleneck (IB) or Min-IB decoding, with significantly fewer parameters to be stored. Additionally, this paper introduces layer-specific RCQ, an extension of RCQ decoding for layered architectures. Layer-specific RCQ uses layer-specific message representations to achieve the best possible FER performance. For layer-specific RCQ, this paper proposes using layered discrete density evolution featuring hierarchical dynamic quantization (HDQ) to design parameters efficiently. Finally, this paper studies field-programmable gate array (FPGA) implementations of RCQ decoders. Simulation results for a (9472, 8192) quasi-cyclic (QC) LDPC code show that a layered Min Sum RCQ decoder with 3-bit messages achieves more than a 10% reduction in LUTs and routed nets and more than a 6% decrease in register usage while maintaining comparable decoding performance, compared to a 5-bit offset Min Sum decoder.

Non-uniform message quantization techniques such as reconstruction-computation-quantization (RCQ) improve error-correction performance and decrease hardware complexity of low-density parity-check (LDPC) decoders that use a flooding schedule. Layered MinSum RCQ (L-msRCQ) enables message quantization to be utilized for layered decoders and irregular LDPC codes. We investigate field-programmable gate array (FPGA) implementations of L-msRCQ decoders. Three design methods for message quantization are presented, which we name the Lookup, Broadcast, and Dribble methods. The decoding performance and hardware complexity of these schemes are compared to a layered offset MinSum (OMS) decoder. Simulation results on a (16384, 8192) protograph-based raptor-like (PBRL) LDPC code show that a 4-bit L-msRCQ decoder using the Broadcast method can achieve a 0.03 dB improvement in error-correction performance while using 12% fewer registers than the OMS decoder. A Broadcast-based 3-bit L-msRCQ decoder uses 15% fewer lookup tables, 18% fewer registers, and 13% fewer routed nets than the OMS decoder, but results in a 0.09 dB loss in performance.