This article proposes a novel eigenvalue-based detector, called Lambda-1 detector, for adaptive and robust interference detection in single-look-complex (SLC) synthetic aperture radar (SAR) images. The proposed method leverages the increased eigenvalues caused by interference in SAR image blocks, where the interference is expected to have a small set of eigenvalues, particularly with a dominating one. Specifically, the method segments the image into multiple blocks, computes the eigenvalues of each block’s covariance matrix, and compares the largest eigenvalue$\lambda _{1}$with a threshold to determine the presence of interference under the criteria of constant false alarm rate (CFAR), thereby enabling adaptive interference detection against varying levels of interference-to-signal ratios (ISRs). The largest eigenvalue is characterized by the order-2 Tracy-Widom distribution (no closed-form expression) under the assumption of the image’s homogeneity, and the threshold is adaptively determined based on a scaled and shifted Gamma distribution that fits this distribution with a closed-form expression. The method is robust by first modeling and then correcting the impacts of upsampling and windowing of SAR image data on the fit distribution’s parameters, and by incorporating outlier removal preprocessing. Experimental results validate the effectiveness of the proposed method in successfully detecting both strong and weak interferences in various SAR images, including Sentinel-1 and Gaofen-3. The detection performance is quantitatively evaluated using false alarm rate$P_{\mathrm { fa}}$and detection rate$P_{d}$. In summary, the proposed Lambda-1 detector effectively identifies interference artifacts in focused SAR images and holds promise for improving the quality of SAR imagery by incorporating adaptive interference removal.

With the change in the spatial angle, the cross-polarization isolation (CPI) of polarimetric phased-array radar (PPAR) changes as well, destroying the estimation of the target polarization scattering matrix (PSM). To correct the bias in PPAR, this article comprehensively designs the transmitting antenna, receiving antenna, and signal waveform and proposes a bias correction method based on system optimization. First, for the transmitting antenna of PPAR, the second-order cone program (SOCP) model is proposed to optimize the weighting coefficient. With the SOCP-based beamforming method, not only beam pattern in any spatial angle can be achieved, but also arbitrary polarization state can be precisely configured. Then, for the wideband receiving signal with a certain beamwidth, an angle estimation method based on eigenvalue decomposition is proposed in this article, which can effectively cure the challenges introduced by the beamwidth and signal bandwidth. Subsequently, for the signal waveform, the phase code is designed to measure all the elements of PSM in simultaneous transmission and simultaneous reception (STSR) mode, which could eliminate the biases of the moving speed and the second-order cross-polarization error. Finally, this article compares with other methods based on differential reflectivity, and experiments show that the factors such as the spatial angle, array structure, antenna beamwidth, signal bandwidth, motion speed, and signal-to-noise ratio (SNR) have the least influence on the present method in this article.

Ship target detection using radar is an important application in military and civilian fields. For the polarization estimation of scattering waves in the underdetermined case, i.e., the number of scattering waves from ships is larger than the number of sensors, this paper proposes two estimation methods with different measurement models. 1) For the single-vector-sensor model, this paper proposes thepolarization-invariantESPRIT-based method. This method can estimate the polarization of signals containing target echo, interference, and noise, which can cure the problem that the accuracy of existing method is poor under low interference signal ratio. 2) For the multi-vector-sensor model, this paper proposes an improved ESPRIT method based on thespatial-invariant and time-invariantsimultaneously, which can increase the degree of freedom without increasing hardware cost. As for another problem of multi-vector-sensor, i.e., almost all existing methods assume that the number of scattering waves is known, this paper introducesthe polarization spectrumfor the first time, which can estimate the polarization parameters when the number of scattering waves is unknown. Finally, we analyze the two proposed ESPRIT-based methods comparing with some existing methods through Monte Carlo simulation, which results demonstrate the efficience of the proposed methods.

Constant false alarm rate (CFAR) detector is a class of widely used methods for target detection in radar images. Classical CFAR detectors perform target detection on a pixel-by-pixel basis using certain sliding windows for estimating clutter statistics, which run fast for small images. However, as the image size gets large, the time cost of these detectors will increase significantly since the time complexity with respect toN×N-pixel image isO(N2). In practice, radar images, such as those in synthetic aperture radar (SAR), usually have very large numbers of pixels (which can be on the order of 10000 × 10000), making the classical CFAR detectors very time-consuming when applied to these images. In this paper, we present graphics processing unit (GPU)-oriented Designs for speeding up CFAR detectors, including smallest/greatest-of CFAR and order-statistic CFAR. The proposed designs implement CFAR detectors via tensor operations, including tensor convolution, shift, and boolean operation, which can be fast operated by GPU. Experiment results show that the proposed GPU-oriented CFAR detectors running on a high-performance Nvidia RTX 3090 GPU can be thousands of times faster than the classical CFAR detectors, and realize real-time target detection in large-size radar images. Examples using SAR and range-Doppler images are provided as illustrative applications of the proposed GPU CFAR detectors to target detection in radar images.

Radio spectrum bands allocated to spaceborne synthetic aperture radar (SAR) imagery are shared by multiple missions. In practical radio spectrum environments, these bands are also used by some ground radars, e.g., C-band weather radar. Due to this fact, radio frequency interference (RFI) may occur for a spaceborne SAR when its received signals contain the transmitted waveforms from another SAR or radar operating at the same frequency band. This particular class of RFI is usually linear-frequency-modulation (LFM) signals, which can cause bright radiometric artifacts in focused SAR images. Most existing signal processing approaches designed for addressing this problem belong to the class of preprocessing methods, which removes RFI in level-0 raw radar data before SAR focusing. In this article, we propose a postprocessing kernel—2-D SPECtral ANalysis (2-D SPECAN) filter, for removing the class of LFM RFI in level-1 SLC images. The filtering consists of three main steps: Step 1: focus LFM RFI artifacts in SLC images as point-like responses in the spectral domain via 2-D SPECAN; Step 2: perform 2-D notch filtering in the spectral domain to remove the most contribution of the RFI responses; and Step 3: transform the filtered spectrum back into the SLC image domain using the inverse operation of the 2-D SPECAN. For computation efficiency, we design a simplified processing flow and adopt a blockwise processing strategy. Experiments with several Sentinel-1 SLC images demonstrate that severe RFI artifacts in SLC images can be removed significantly by the proposed method.