Recently, several energy reduction techniques using DVFS have been presented for PC clusters. This work proposes a Code-instrumented Runtime DVFS control, in which the combination of frequency and voltage (called a gear) is managed at the instrumented code at runtime. The codes are inserted by defining the program regions that have the same characteristics. The Code-instrumented Runtime DVFS control method is better than the Interrupt-based Runtime DVFS control method, in which the gear is managed by periodic interrupt, because it can reflect the program information to control DVFS. Though Static DVFS control, which makes use of the power profile before execution, gives better energy reduction, the proposed Code-instrumented Runtime DVFS control is easier to use, because it requires no information such as profile. The proposed DVFS control method was designed and implemented. The beta-adaptation was used as the runtime algorithm to choose the appropriate gear. The results show that the proposed method can improve the performance and energy consumption compared with Interrupt-based Runtime DVFS control. Although our Code-instrumented Runtime DVFS control can select lower voltages and frequencies than the present Runtime DVFS control given a certain deadline, unfortunately, it was also found to increase power consumption of the PC cluster due to an increase in the execution time.

In this paper, we propose a scheme based on server node state control, including stand-by/wake-up and processor power control, to achieve aggressive power education while satisfying Quality of Service (QoS). Decreasing power consumption on Web servers is currently a challenging new problem to be solved in a data center or warehouse. Although Web servers are configured to have maximum performance, the actual access rate to the servers can be small in a specific period, such as midnight, so it may be possible to reduce the power consumption of the servers while satisfying QoS with lower server performance. In order to reduce power consumption on the server nodes, we now have to consider the power consumption of the entire node rather than only processor power by Dynamic Voltage and Frequency Scaling (DVFS). We implemented the proposed scheme to the distributed Web server system using the power-profile of server nodes and considering load increment based on traffic prediction method and evaluated the proposed scheme with a Web server benchmark workload based on SPECWeb99. The result reveals that the proposed scheme achieved an energy saving of approximately 17% with sufficient QoS performance on the distributed Web server system.

It has become important to improve the energy efficiency of high performance PC clusters. In PC clusters, high-performance microprocessors have a dynamic voltage and frequency scaling (DVFS) mechanism, which allows the voltage and frequency to be set for reduction in energy consumption. In this paper, we proposed a new algorithm that reduces energy consumption in a parallel program executed on a power-scalable cluster using DVFS. Whenever the computational load is not balanced, parallel programs encounter slack time, that is, they must wait for synchronization of the tasks. Our algorithm reclaims slack time by changing the voltage and frequency, which allows a reduction in energy consumption without impacting on the performance of the program. Our algorithm can be applied to parallel programs represented by a directed acyclic task graph (DAG). It selects an appropriate set of voltages and frequencies (called the gear) that allow the tasks to execute at the lowest frequency that does not increase the overall execution time, but at the same time allows the tasks to be executed as uniformly as possible in frequency. We built two different types of power-scalable clusters using AMD Turion and Transmeta Crusoe. For the empirical study on energy reduction in PC clusters, we designed a toolkit called PowerWatch that includes power monitoring tools and the DVFS control library. This toolkit precisely measures the power consumption of the entire cluster in real time. The experimental results using benchmark problems show that our algorithm reduces energy consumption by 25% with only a 1 % loss in performance

In our research project named "Mega-Scale Computing Based on Low-Power Technology and Workload Modeling", we have been developing a prototype cluster not based on ASIC or FPGA but instead only using commodity technology. Its packaging is extremely compact and dense, and its performance/power ratio is very high. Our previous prototype system named "MegaProto" demonstrated that one cluster unit, which consists of 16 commodity low-power processors, can be successfully implemented on just 1U height chassis and it is capable of up to 2.8 times higher performance/power ratio than ordinary high-performance dual-Xeon 1U server units. We have improved MegaProto by replacing the CPU and enhancing the I/O performance. The new cluster unit named "MegaProto/E" with 16 Transmeta Efficeon processors achieves 32 GFlops of peak performance, which is 2.2-fold greater than that of the original one. The cluster unit is equipped with an independent dual network of Gigabit Ethernet, including dual 24-port switches. The maximum power consumption of the cluster unit is 320 W, which is comparable with that of today's high-end PC servers for high performance clusters. Performance evaluation using NPB kernels and HPL shows that the performance of MegaProto/E exceeds that of a dual-Xeon server in all the benchmarks, and its performance ratio ranges from 1.3 to 3.7. These results reveal that our solution of implementing a number of ultra low-power processors in compact packaging is an excellent way to achieve extremely high performance in applications with a certain degree of parallelism. We are now building a multi-unit cluster with 128 CPUs (8 units) to prove that this advantage still holds with higher scalability

Currently, several of the high performance processors used in a PC cluster have a DVS (dynamic voltage scaling) architecture that can dynamically scale processor voltage and frequency. Adaptive scheduling of the voltage and frequency enables us to reduce power dissipation without a performance slowdown during communication and memory access. In this paper, we propose a method of profiled-based power-performance optimization by DVS scheduling in a high-performance PC cluster. We divide the program execution into several regions and select the best gear for power efficiency. Selecting the best gear is not straightforward since the overhead of DVS transition is not free. We propose an optimization algorithm to select a gear using the execution and power profile by taking the transition overhead into account. We have built and designed a power-profiling system, PowerWatch. With this system we examined the effectiveness of our optimization algorithm on two types of power-scalable clusters (Crusoe and Turion). According to the results of benchmark tests, we achieved almost 40% reduction in terms of EDP (energy-delay product) without performance impact (less than 5%) compared to results using the standard clock frequency.

In our research project "Mega-Scale Computing Based on Low-Power Technology and Workload Modeling", we claim that a million-scale parallel system could be built with densely mounted low-power commodity processors. "MegaProto" is a proof-of-concept low-power and highperformance cluster build only with commodity components to implement this claim. A one-rack system is composed of 32 motherboard "cluster units" of 1 U-height and commodity switches to interconnect them mutually as well as with other racks. Each cluster unit houses 16 low-power dollarbill- sized commodity PC-architecture daughterboards, together with a high bandwidth, 2 Gbps per processor embedded switched network based on Gigabit Ethernet. The peak performance of a one-rack system is 0.48 TFlops for the first version and will improve to 1.02 TFlops in the second version through a processor/daughterboard upgrade. The system consumes about 10 kW or less per rack, resulting in 100 MFlops/W power efficiency with a power-aware intrarack network of 32 Gbps bisection bandwidth, while additional 2.4 kW will boost this to sufficiently large 256 Gbps. Performance studies show that even the first version significantly outperforms a conventional high-end 1U server comprised of dual power-hungry processors in a majority of NPB programs. It is also investigated how the current automated DVS control could save power for the HPC parallel programs along with its limitation.