In safety-critical SoC applications such as automotive and aerospace, reliable transaction monitoring is crucial for maintaining system integrity. This paper introduces a drop-in Transaction Monitoring Unit (TMU) for AXI4 subordinate endpoints that detects transaction failures including protocol violations or timeouts and triggers recovery by resetting the affected subordinates. Two TMU variants address different constraints: a Tiny-Counter solution for tightly area-constrained systems and a Full-Counter solution for critical subordinates in mixed-criticality SoCs. The Tiny-Counter employs a single counter per outstanding transaction, while the Full-Counter uses multiple counters to track distinct transaction stages, offering finer-grained monitoring and reducing detection latencies by up to hundreds of cycles at roughly 2.5x the area cost. The Full-Counter also provides detailed error logs for performance and bottleneck analysis. Evaluations at both IP and system levels confirm the TMU's effectiveness and low overhead. In GF12 technology, monitoring 16–32 outstanding transactions occupies$1330-2616 \mu \mathrm{m}^{2}$for the Tiny-Counter and 3452–6787$\mu \mathrm{m}^{2}$for the Full-Counter; moderate prescaler steps reduce these figures by 18–39 % and 19–32 %, respectively, with no loss of functionality. Results from a full-system integration demonstrate the TMU's robust and precise monitoring capabilities in safety-critical SoC environments.

End-to-end open-source electronic design automation enables a collaborative approach to chip design conducive to supply chain diversification and zero-trust step-by-step design verification. However, existing end-to-end OSEDA flows have mostly been demonstrated on small designs and have not yet enabled large, industry-grade chips such as Linux-capable systems-on-chip (SoCs). This work presents Basilisk, the largest end-to-end open-source SoC to date. Basilisk’s 34mm2, 2.7MGE design features a 64-bit Linuxcapable RISC-V core, a lightweight 124MB/s DRAM controller, and extensive IO, including a USB 1.1 host, a video output, and a fully digital 62Mb/s chip-to-chip (C2C) link. We implement Basilisk in IHP’s open 130nm BiCMOS technology, significantly improving on the state-of-the-art (SoA) OSEDA flow. Our enhancements of the Yosys-based synthesis flow improve design timing and area by 2.3×and 1.6×, respectively, while consuming significantly less system resources. By tuning OpenROAD place and route (P&R) to our design and technology, we decrease the die size by 12%. The fabricated Basilisk chip reaches 62MHz at its nominal 1.2V core voltage and up to 102MHz at 1.64V. It achieves a peak energy efficiency of 18.9DPMFLOP/s/W at 0.88V.

Energy-centric design is paramount in the current embedded computing era: use cases require increasingly high performance at an affordable power budget, often under real-time constraints. Hardware heterogeneity and parallelism help address the efficiency challenge, but greatly complicate online power consumption assessments, which are essential for dynamic hardware and software stack adaptations. We introduce a novel power modeling methodology with state-of-the-art accuracy, low overhead, and high responsiveness, whose implementation does not rely on microarchitectural details. Our methodology identifies the Performance Monitoring Counters (PMCs) with the highest linear correlation to the power consumption of each hardware sub-system, for each Dynamic Voltage and Frequency Scaling (DVFS) state. The individual, simple models are composed into a complete model that effectively describes the power consumption of the whole system, achieving high accuracy and low overhead. Our evaluation reports an average estimation error of 7.5 % for power consumption and 1.3 % for energy. We integrate these models in the Linux kernel with Runmeter, an open-source, PMC-based monitoring framework. Runmeter manages PMC sampling and processing, enabling the execution of our power models at runtime. With a worst-case time overhead of only 0.7 %, Runmeter provides responsive and accurate power measurements directly in the kernel. This information can be employed for actuation policies in workload-aware DVFS and power-aware, closed-loop task scheduling.

The automotive industry is transitioning from federated, homogeneous, interconnected devices to integrated, heterogeneous, mixed-criticality systems (MCS). This leads to challenges in achieving timing predictability techniques due to access contention on shared resources, which can be mitigated using hardware-based spatial and temporal isolation techniques. Focusing on the interconnect as the point of access for shared resources, we propose AXI-REALM, a lightweight, modular, technology-independent, and open-source real-time extension to AXI4 interconnects. AXI-REALM uses a budget-based mechanism enforced on periodic time windows and transfer fragmentation to provide fair arbitration, coupled with execution predictability on real-time workloads. AXI-REALM features a comprehensive bandwidth and latency monitor at both the ingress and egress of the interconnect system. Latency information is also used to detect and reset malfunctioning subordinates, preventing missed deadlines. We provide a detailed cost assessment in a 12nm node and an end-to-end case study implementing AXI-REALM into an open-source MCS, incurring an area overhead of less than 2 %. When running a mixed-criticality workload, with a time-critical application sharing the interconnect with non-critical applications, we demonstrate that the critical application can achieve up to 68.2% of the isolated performance by enforcing fairness on the interconnect traffic through burst fragmentation, thus reducing the subordinate access latency by up to 24 times. Near-ideal performance, (above 95% of the isolated performance) can be achieved by distributing the available bandwidth in favor of the critical application.

The new generation of domain-specific AI accelerators is characterized by rapidly increasing demands for bulk data transfers, as opposed to small, latency-critical cache line transfers typical of traditional cache-coherent systems. In this article, we address this critical need by introducing the FlooNoC network-on-chip (NoC), featuring very wide, fully advanced extensible interface (AXI4) compliant links designed to meet the massive bandwidth needs at high energy efficiency. At the transport level, nonblocking transactions are supported for latency tolerance. In addition, a novel end-to-end ordering approach for AXI4, enabled by a multistream capable direct memory access (DMA) engine, simplifies network interfaces (NIs) and eliminates interstream dependencies. Furthermore, dedicated physical links are instantiated for short, latency-critical messages. A complete end-to-end reference implementation in 12-nm FinFET technology demonstrates the physical feasibility and power performance area (PPA) benefits of our approach. Using wide links on high levels of metal, we achieve a bandwidth of 645 Gb/s/link and a total aggregate bandwidth of 103 Tb/s for an$8\times 4$mesh of processors’ cluster tiles, with a total of 288 RISC-V cores. The NoC imposes a minimal area overhead of only 3.5% per compute tile and achieves a leading-edge energy efficiency of 0.15 pJ/B/hop at 0.8 V. Compared with state-of-the-art (SoA) NoCs, our system offers three times the energy efficiency and more than double the link bandwidth. Furthermore, compared with a traditional AXI4-based multilayer interconnect, our NoC achieves a 30% reduction in area, corresponding to a 47% increase in GFLOPSDP within the same floorplan.

The increasing demand for heterogeneous functionality in the automotive industry and the evolution of chip manufac-turing processes have led to the transition from federated to integrated critical real-time embedded systems (CRTESs). This leads to higher integration challenges of conventional timing predictability techniques due to access contention on shared resources, which can be resolved by providing system-level observability and controllability in hardware. We focus on the interconnect as a shared resource and propose AXI-REALM, a lightweight, modular, and technology - independent real-time extension to industry-standard AXI4 interconnects, available open-source. AXI-REALM uses a credit-based mechanism to distribute and control the bandwidth in a multi-subordinate system on periodic time windows, proactively prevents denial of service from malicious actors in the system, and tracks each manager's access and interference statistics for optimal budget and period selection. We provide detailed performance and implementation cost assessment in a 12nm node and an end-to-end functional case study implementing AXI-REALM into an open-source Linux-capable RISC-V SoC. In a system with a general-purpose core and a hardware accelerator's DMA engine causing interference on the interconnect, AXI-REALM achieves fair bandwidth distribution among managers, allowing the core to recover 68.2 % of its performance compared to the case without contention. Moreover, near-ideal performance (above 95 %) can be achieved by distributing the available bandwidth in favor of the core, improving the worst-case memory access latency from 264 to below eight cycles. Our approach minimizes buffering compared to other solutions and introduces only 2.45 % area overhead compared to the original SoC.

Sparse matrix-vector multiplication (SpMV) is central to numerous data-intensive applications, but requires streaming indirect memory accesses that severely degrade both processing and memory throughput in state-of-the-art architectures. Near-memory hardware units, decoupling indirect streams from processing elements, partially alleviate the bottleneck, but rely on low DRAM access granularity, which is highly inefficient for modern DRAM standards like HBM and LPDDR. To fully address the end-to-end challenge, we propose a low-overhead data coa- lescer combined with a near-memory indirect streaming unit for AXI-Pack, an extension to the widespread AXI4 protocol packing narrow irregular stream elements onto wide memory buses. Our combined solution leverages the memory-level parallelism and coalescence of streaming indirect accesses in irregular applications like SpMV to maximize the performance and bandwidth efficiency attained on wide memory interfaces. Our solution delivers an average speedup of 8x in effective indirect access, often reaching the full memory bandwidth. As a result, we achieve an average end-to-end speedup on SpMV of 3x. Moreover, our approach demonstrates remarkable on-chip efficiency, requiring merely 27kB of on-chip storage and a very compact implementation area of O.2-0.3mm2in a 12nm node.

Data transfers are essential in today's computing systems as latency and complex memory access patterns are increasingly challenging to manage. Direct memory access engines (DMAES) are critically needed to transfer data independently of the processing elements, hiding latency and achieving high throughput even for complex access patterns to high-latency memory. With the prevalence of heterogeneous systems, DMAEs must operate efficiently in increasingly diverse environments. This work proposes a modular and highly configurable open-source DMAE architecture called intelligent DMA (iDMA), split into three parts that can be composed and customized independently. The front-end implements the control plane binding to the surrounding system. The mid-end accelerates complex data transfer patterns such as multi-dimensional transfers, scattering, or gathering. The back-end interfaces with the on-chip communication fabric (data plane). We assess the efficiency of iDMA in various instantiations: In high-performance systems, we achieve speedups of up to 15.8$\boldsymbol{\times}$with only 1% additional area compared to a base system without a DMAE. We achieve an area reduction of 10% while improving ML inference performance by 23% in ultra-low-energy edge AI systems over an existing DMAE solution. We provide area, timing, latency, and performance characterization to guide its instantiation in various systems.

Emerging deep neural network (DNN) applications require high-performance multi-core hardware acceleration with large data bursts. Classical network-on-chips (NoCs) use serial packet-based protocols suffering from significant protocol translation overheads towards the endpoints. This paper proposes PATRONoC, an open-source fully AXI-compliant NoC fabric to better address the specific needs of multi-core DNN computing platforms. Evaluation of PATRONoC in a 2D-mesh topology shows 34 % higher area efficiency compared to a state-of-the-art classical NoC at 1 GHz. PATRONoC’s throughput outperforms a baseline NoC by 2-8× on uniform random traffic and provides a high aggregated throughput of up to 350 GiB/s on synthetic and DNN workload traffic.

Data-intensive applications involving irregular memory streams are inefficiently handled by modern processors and memory systems highly optimized for regular, contiguous data. Recent work tackles these inefficiencies in hardware through core-side stream extensions or memory-side prefetchers and accelerators, but fails to provide end-to-end solutions which also achieve high efficiency in on-chip interconnects. We propose AXI-Pack, an extension to ARM's AXI4 protocol introducing bandwidth-efficient strided and indirect bursts to enable end-to-end irregular streams. AXI-Pack adds irregular stream semantics to memory requests and avoids inefficient narrow-bus transfers by packing multiple narrow data elements onto a wide bus. It retains full compatibility with AXI4 and does not require modifications to non-burst-reshaping interconnect IPs. To demonstrate our approach end-to-end, we extend an open-source RISC-V vector processor to leverage AXI-Pack at its memory interface for strided and indexed accesses. On the memory side, we design a banked memory controller efficiently handling AXI-Pack requests. On a system with a 256-bit-wide interconnect running FP32 workloads, AXI-Pack achieves near-ideal peak on-chip bus utilizations of 87% and 39%, speedups of 5.4x and 2.4x, and energy efficiency improvements of 5.3x and 2.1x over a baseline using an AXI4 bus on strided and indirect benchmarks, respectively.

On-chip communication infrastructure is a central component of modern systems-on-chip (SoCs), and it continues to gain importance as the number of cores, the heterogeneity of components, and the on-chip and off-chip bandwidth continue to grow. Decades of research on on-chip networks enabled cache-coherent shared-memory multiprocessors. However, communication fabrics that meet the needs of heterogeneous many-cores and accelerator-rich SoCs, which are not, or only partially, coherent, are a much less mature research area. In this work, we present a modular, topology-agnostic, high-performance on-chip communication platform. The platform includes components to build and link subnetworks with customizable bandwidth and concurrency properties and adheres to a state-of-the-art, industry-standard protocol. We discuss microarchitectural trade-offs and timing/area characteristics of our modules and show that they can be composed to build high-bandwidth (e.g., 2.5 GHz and 1024 bit data width) end-to-end on-chip communication fabrics (not only network switches but also DMA engines and memory controllers) with high degrees of concurrency. We design and implement a state-of-the-art ML training accelerator, where our communication fabric scales to 1024 cores on a die, providing 32 TB/s cross-sectional bandwidth at only 24 ns round-trip latency between any two cores.

The capacity of offloading data and control tasks to the network is becoming increasingly important, especially if we consider the faster growth of network speed when compared to CPU frequencies. In-network compute alleviates the host CPU load by running tasks directly in the network, enabling additional computation/communication overlap and potentially improving overall application performance. However, sustaining bandwidths provided by next-generation networks, e.g., 400 Gbit/s, can become a challenge. sPIN is a programming model for in-NIC compute, where users specify handler functions that are executed on the NIC, for each incoming packet belonging to a given message or flow. It enables a CUDA-like acceleration, where the NIC is equipped with lightweight processing elements that process network packets in parallel. We investigate the architectural specialties that a sPIN NIC should provide to enable high-performance, low-power, and flexible packet processing. We introduce PsPIN, a first open-source sPIN implementation, based on a multi-cluster RISC-V architecture and designed according to the identified architectural specialties. We investigate the performance of PsPIN with cycle-accurate simulations, showing that it can process packets at 400 Gbit/s for several use cases, introducing minimal latencies (26 ns for 64 B packets) and occupying a total area of 18.5 mm2(22 nm FDSOI).

Fully Electric Vehicles (FEVs) represent a promising solution for the reduction of fuel consumption, air and noise pollution in urban areas. However, the commercial viability of FEVs is at stake if the associated issues of autonomy are not dealt with effectively. Project EcoGem - Cooperative Advanced Driver Assistance System for Green Cars - advocates that the success and user acceptability of FEVs will predominantly depend on their electrical energy consumption rate and the corresponding degree of autonomy that they can offer. EcoGem aims at providing efficient ICT-based solutions to this great issue, by designing and developing a FEV-oriented highly-intelligent Advanced Driver Assistance System, equipped with suitable monitoring, learning, reasoning and management capabilities that will help increase the FEV's autonomy and energy efficiency.