This study proposes a complete solution to make the humanoid robot HRP-2 dynamically step over large obstacles. As compared with previous results using quasistatic stability, where the robot crosses over a 15-cm obstacle in 40 s, our solution allows HRP-2 to step over the same obstacle in 4 s. This approach allows the robot to clear obstacles as high as 21% of the robot's leg length (15 cm) while walking. Simulations show the possibility to step over an obstacle that is 35% of the length (25 cm) with a margin of 3 cm.

Kikuuwe and Fujimoto have introduced proxy-based sliding mode control. It combines responsive and accurate tracking during normal operation with smooth, slow recovery from large position errors that can sometimes occur after abnormal events. The method can be seen as an extension to both conventional PID control and sliding mode control. In this paper, proxy-based sliding mode control is used to control a 2-DOF planar manipulator actuated by pleated pneumatic artificial muscles (PPAMs). The principal advantage of this control method is increased safety for people interacting with the manipulator. Two different forms of proxy-based sliding mode control were implemented on the system, and their performance was experimentally evaluated. Both forms performed very well with respect to safety. Good tracking was also obtained, especially with the second form.

This video demonstrates our current investigation in developing autonomous behaviors for humanoid robots. Our main goal is to develop functionalities as much generic as possible in order to realize useful behaviors. More particularly this video demonstrates our current status on extending a popular zero momentum problem (ZMP) preview control based pattern generator, and building some links between walking with vision.

In this paper a novel rotational actuator with adaptable compliance is presented. First the importance of adaptable compliance for bipedal walking is explained, and then a number of comparable designs are given with their possible drawbacks. The MACCEPA concept and design is described in detail. The formula to calculate the generated torque is derived. It is shown, depending on the design parameters, that the torque is a quasi linear function with respect to the angle between equilibrium position and actual position. Also the change of the pre-tension has a quasi linear effect on the torque. Another advantage is that the actuator can be built with standard components, e.g. electrical servo motors. Experiments show the independent control of equilibrium position and compliance. Finally, the concept of controlled passive walking is explained, which is a combination of the control strategies of active and passive walking robots. Controlled passive walking requires actuators with adaptable compliance, preferably where the control of equilibrium position and compliance are independent

In the biped Lucy pleated pneumatic artificial muscles are used instead of electrical motors to power the joints, because in an antagonistic set-up both the torque and the compliance are controllable. The muscles have also a high power to weight ratio and they can reduce impact effects. Interesting characteristics that can be exploited for legged robots. In this paper a control strategy is discussed where a torque control unit tracks a predefined trajectory and a compliance controller is used to reduce control efforts and energy consumption by fitting the compliance of the actuator to the natural compliance of the desired trajectory. The first part of this paper focusses on the torque control unit for the biped. The proposed control architecture consists of the joint trajectory generator and the joint trajectory tracking controller. The trajectory generator calculates trajectories represented by polynomials based on objective locomotion parameters, which are average forward speed, step length, step height and intermediate foot lift. The joint trajectory tracking controller is divided in three parts: a computed torque module, a delta-p unit and a bang-bang pressure controller. Results of the incorporation of this control architecture in the real biped Lucy are given. Several essential graphs showing tracking performance and pressure regulation are given and the effectiveness of the control algorithm is discussed. A second part of the paper focusses on the compliance controller which is experimentally tested on a one DOF pendulum. A mathematical formulation to exploit the natural dynamics with respect to different walking patterns for this purpose is explained. The experimental results show the effectiveness and importance of the adaptation strategy

This paper reports on the control structure of the pneumatic biped Lucy. The robot is actuated with pleated pneumatic artificial muscles, which have interesting characteristics that can be exploited for legged machines. They have a high power to weight ratio, an adaptable compliance and they can reduce impact effects. The discussion of the control architecture focusses on the joint trajectory generator and the tracking controller which is divided in four parts: a computed torque module, an inverse delta-p unit, a local PI controller and a bang-bang pressure controller. The control design is divided into single support and double support where specifically the computed torque differs for these two phases. A full hybrid dynamic simulation model is used to evaluate the control architecture of the biped. This simulator combines the dynamical behaviour of the robot with the thermodynamical effects that take place in the muscle-valves system. The observed hardware limitations of the real robot and expected model errors are taken into account in order to give a realistic qualitative evaluation of the control performance and to test the robustness. Finally the first results of the incorporation of this control architecture in the real biped Lucy are given.

Pleated pneumatic artificial muscles (PPAMs), developed at the Vrije Universiteit Brussel, Department of Mechanical Engineering, are used as robotic actuators. Their distinguishing feature is their pleated design, as a result of which their contraction forces and maximum displacement are very high compared to other pneumatic artificial muscles. The PPAM design, operation and characteristics are presented. A rotative joint actuator, made of two antagonistically coupled PPAMs, is discussed to demonstrate their suitability for robotics. It has several properties that are similar to those of skeletal joint actuators. Positioning tasks are seen to be performed very accurately using a simple PI control. Furthermore, the antagonistic actuator can easily be made to have a soft or careful touch, contributing greatly to a safe robot operation. In view of all the characteristics PPAMs are very well suited for automation and robotic applications.