Bluetooth is an omnipresent technology, available on billions of devices today. While it has been traditionally limited to peer-to-peer communication and star networks, the recent Bluetooth Mesh standard extends it to multi-hop networking. In addition, the Bluetooth 5 standard introduces new modes to allow for increased reliability. In this article, we evaluate the feasibility of concurrent transmissions (CT) in Bluetooth via modeling and controlled experiments and then devise an efficient network-wide data dissemination protocol, BlueFlood, based on CT for multi-hop Bluetooth networks. First, we model and analyze how CT distorts the received waveform and characterize the Bit Error Rate of a Frequency-Shift Keying receiver to show that CT is feasible over Bluetooth. Second, we verify our analytic results with a controlled experimental study of CT over Bluetooth PHY. Third, we present BlueFlood, a fast and efficient network-wide data dissemination in multi-hop Bluetooth networks. In our experimental evaluation, in two testbeds deployed in university buildings, we show that BlueFlood achieves 99.9% end-to-end delivery ratio with a duty-cycle of 0.4% for periodic dissemination of advertising packets of 38 bytes with 200 milliseconds intervals at 2 Mbps. Moreover, we show that BlueFlood can be received by off-the-shelf devices such as smartphones, paving a seamless integration with existing technologies.

Synchronized communication has recently emerged as a prime option for low-power critical applications. Solutions such as Glossy or Time Slotted Channel Hopping (TSCH) have demonstrated end-to-end reliability upwards of 99.99%. In this context, the IETF Working Group 6TiSCH is currently standardizing the mechanisms to use TSCH in low-power IPv6 scenarios. This paper identifies a number of challenges when it comes to implementing the 6TiSCH stack. It shows how these challenges can be addressed with practical solutions for locking, queuing, scheduling and other aspects. With this implementation as an enabler, we present an experimental validation and comparison with state-of-the-art MAC protocols. We conduct fine-grained energy profiling, showing the impact of link-layer security on packet transmission. We evaluate distributed time synchronization in a 340-node testbed, and demonstrate that tight synchronization (hundreds of microseconds) can be achieved at very low cost (0.3% duty cycle, 0.008% channel utilization). We finally compare TSCH against traditional MAC layers: low-power listening (LPL) and CSMA, in terms of reliability, latency and energy. We show that with proper scheduling, TSCH achieves by far the highest reliability, and outperforms LPL in both energy and latency.

In low-power wireless networking, new applications such as cooperative robots or industrial closed-loop control demand for network-wide consensus at low-latency and high reliability. Distributed consensus protocols is a mature field of research in a wired context, but has received little attention in low-power wireless settings. In this paper, we present A2: Agreement in the Air, a system that brings distributed consensus to low-power multi-hop networks. A2 introduces Synchrotron, a synchronous transmissions kernel that builds a robust mesh by exploiting the capture effect, frequency hopping with parallel channels, and link-layer security. A2 builds on top of this reliable base layer and enables the two- and three-phase commit protocols, as well as network services such as group membership, hopping sequence distribution and re-keying.

Many protocols in low-power wireless networks require a root node or a leader to bootstrap and maintain its operation. For example, Chaos and Glossy networks need an initiator to synchronize and initiate the communications rounds. Commonly, these protocols use a fixed, compile-time defined node as the leader. In this work, we tackle the challenge of dynamically bootstrapping the network and electing a leader in low-power wireless scenarios, and we focus on Chaos-style networks.

Time slotted operation is a well-proven approach to achieve highly reliable low-power networking through scheduling and channel hopping. It is, however, difficult to apply time slotting to dynamic networks as envisioned in the Internet of Things. Commonly, these applications do not have pre-defined periodic traffic patterns and nodes can be added or removed dynamically.

Exploiting multiple radio channels for communication has been long known as a practical way to mitigate interference in wireless settings. In Wireless Sensor Networks, however, multi-channel solutions have not reached their full potential: the MAC layers included in TinyOS or the Contiki OS for example are mostly single-channel. The literature offers a number of interesting solutions, but experimental results were often too few to build confidence. We propose a practical extension of low-power listening, MiCMAC, that performs channel hopping, operates in a distributed way, and is independent of upper layers of the protocol stack. The above properties make it easy to deploy in a variety of scenarios, without any extra configuration/scheduling/channel selection hassle. We implement our solution in Contiki and evaluate it in a 97-node~testbed while running a complete, out-of-the-box low-power IPv6 communication stack (UDP/RPL/6LoWPAN). Our experimental results demonstrate increased resilience to emulated WiFi interference (e.g., data yield kept above 90% when Contiki MAC drops in the 40% range). In noiseless environments, MiCMAC keeps the overhead low in comparison to Contiki MAC, achieving performance as high as 99% data yield along with sub-percent duty cycle and sub-second latency for a 1-minute inter-packet interval data collection.