Tree fruit growers around the world are facing labor shortages for critical operations, including harvest and pruning. There is a great interest in developing robotic solutions for these labor-intensive tasks, but current efforts have been prohibitively costly, slow, or require a reconfiguration of the orchard in order to function. In this paper, we introduce an alternative approach to robotics using a novel and low-cost soft-growing robotic platform. Our platform features the ability to extend up to 1.2 m linearly at a maximum speed of 0.27 m/s. The soft-growing robotic arm can operate with a terminal payload of up to 1.4 kg (4.4 N), more than sufficient for carrying an apple. This platform decouples linear and steering motions to simplify path planning and the controller design for targeting. We anticipate our platform being relatively simple to maintain compared to rigid robotic arms. Herein we also describe and experimentally verify the platform's kinematic model, including the prediction of the relationship between the steering angle and the angular positions of the three steering motors. Information from the model enables the position controller to guide the end effector to the targeted positions faster and with higher stability than without this information. Overall, our research show promise for using soft-growing robotic platforms in orchard operations.

Soft growing robots are proposed for use in applications such as complex manipulation tasks or navigation in disaster scenarios. Safe interaction and ease of production promote the usage of this technology, but soft robots can be challenging to teleoperate due to their unique degrees of freedom. In this paper, we propose a human-centered interface that allows users to teleoperate a soft growing robot for manipulation tasks using arm movements. A study was conducted to assess the intuitiveness of the interface and the performance of our soft robot, involving a pick-and-place manipulation task. The results show that users were able to complete the task 97% of the time and achieve placement errors below 2 cm on average. These results demonstrate that our body-movement-based interface is an effective method for control of a soft growing robot manipulator.

Pneumatically operated soft growing robots that extend via tip eversion are well-suited for navigation in confined spaces. Adding the ability to interact with the environment using sensors and tools attached to the robot tip would greatly enhance the usefulness of these robots for exploration in the field. However, because the material at the tip of the robot body continually changes as the robot grows and retracts, it is challenging to keep sensors and tools attached to the robot tip during actuation and environment interaction. In this paper, we analyze previous designs for mounting to the tip of soft growing robots, and we present a novel device that successfully remains attached to the robot tip while providing a mounting point for sensors and tools. Our tip mount incorporates and builds on our previous work on a device to retract the robot without undesired buckling of its body. Using our tip mount, we demonstrate two new soft growing robot capabilities: (1) pulling on the environment while retracting, and (2) retrieving and delivering objects. Finally, we discuss the limitations of our design and opportunities for improvement in future soft growing robot tip mounts.

This paper presents an origami-inspired cable-driven continuum manipulator module that offers low-cost, low-volume deployment, light weight, and inherently safe human interaction and collaboration. Each module has a mass of around 110 g and integrates the actuation, sensing, and control sub-systems necessary for operation. The origami structure has 7.311 Nm/rad (0.128 Nm/degree) torsional stiffness while being capable of bending in two directions and changing arclength down to a fully collapsed state. A maximum contraction of 35 mm and bending angle of 35.5 degrees were achieved with 45 mm arc length. The module is capable of passively supporting a 1-kg mass at its tip, or 4 additional serially connected modules, bending approximately 6 degrees in the worst case. We also show that we can actively compensate for external moments by pre-compressing or pre-bending the module. We utilize an inverse kinematic control scheme and use it for both open and closed loop control following a circular trajectory. Our results indicate that the module motion follows the desired trajectory with an RMS error of 0.681 mm in the horizontal (x-y) plane and 0.373 mm in the z-axis with closed-loop control. We also assembled two origami modules in series and drove them independently, demonstrating the proof-of-concept of a modular origami continuum manipulator.

Soft robotics carries the promise of making robots as capable and adaptable as biological creatures, but this will not be possible without the ability to perform self-sensing and control with precision and repeatability. In this paper, we seek to address this need with the development of a new pneumatically-actuated soft bending actuation module with integrated curvature sensing. We designed and fabricated two different versions of this module: One with a commercially available resistive flex sensor and the other with a magnetic curvature sensor of our own design, and used an external motion capture system to calibrate and validate these two approaches. In addition, we used an iterative sliding mode controller to drive the modules through step curvature references to demonstrate the controllability of the modules as well as compare the usability of the two sensors. We found that the magnetic sensor returned noisy but accurate data, while the flex sensor had minor inaccuracies and it was subject to overshoot but did not exhibit notable noise. Experimental results show that this phenomenon of overshoot from the flex sensor causes active feedback control of the bending actuator to exhibit significant positioning errors. This work demonstrates that our soft bending actuator can be controlled with repeatability and precision, and that our magnetic curvature sensor represents an improvement for use in proprioception and closed-loop control of soft robotic devices.

Soft pneumatic actuators can allow robotic manipulators to interact safely in complex environments in close proximity to humans, but work still needs to be done controlling them more effectively. We explore this area by introducing a 2-degree of freedom (DoF) universal joint module actuated by three reverse Pneumatic Artificial Muscles (rPAMs) and an associated geometric Jacobian-enhanced iterative sliding mode controller. After demonstrating the effectiveness of this controller, we combine two of these modules to form a 4-DoF soft actuated manipulator. To control this modular manipulation system, we propose two controllers: a direct inverse kinematic (IK) controller and an end-effector geometric Jacobian controller. Though both controllers were validated to function effectively, the Jacobian controller was more precise (especially under payload) while the IK controller was more accurate.

Soft pneumatic actuators provide many exciting properties, but controlling them without the use of bulky and expensive flow-control valves can be difficult and computationally expensive. We seek a solution to this problem by introducing an inexpensive and reliable muscle-like linear soft actuator used antagonistically to operate a rigid 1-DoF joint, resulting in a system that combines the advantages of rigid and soft robotics. Using this setup, we performed precise motion control using a sliding mode feedback controller as well as a sliding mode controller augmented by a feedforward term to modulate the state of solenoid valves that drive each actuator. We found that both controllers performed equivalently well in following a step function and in responding to a disturbance. The feedforward augmented controller performed significantly better when following dynamic trajectories over a range of frequencies and with the addition of an external force. The next step will be to modify our valve control scheme to allow for the determination of both the position and stiffness of the joint, better leveraging the advantages of soft pneumatic actuators.