Community-based locomotor training post-stroke has shown improvements in independent ambulation by increasing dose, intensity, and specificity of walking practice. Robotic ankle exoskeletons hold the potential to facilitate continued rehabilitation at home, but understanding what aspects of the design are most relevant for successful translation to the community presents a challenge. Here, we design a portable rigid ankle exoskeleton to use as a research platform for investigating the effect of assistance on post-stroke gait during overground, community-based walking. We first test our device with stroke survivors and validate its potential for future community use. We then present a systematic method for quantifying power transmission losses at each transmission stage from the battery to the wearer, using data gathered from walking trials with healthy participants. Our evaluation method revealed inefficiencies in power transfer at the interface level, likely resulting from the compliance in the structural components of the system, which motivates future redesign considerations. Overall, our method provides a framework to identify and characterize the components that must be redesigned to lower exoskeleton weight and maximize performance.

We present an autonomous and portable hip-only soft exosuit, for augmenting human walking and running that assists hip extension by delivering peak forces of 300N to the user. Different fixed assistance profiles for walking and running were applied based on an online classification algorithm. The approach is based on the biomechanical understanding that the center of mass potential energy fluctuations during walking and running are out of phase. Specifically, we monitor the vertical acceleration with an abdomen-mounted IMU at the moment of maximum hip extension. Validation is demonstrated with six subjects on the treadmill and with eight subjects outdoors. Our results demonstrated a 99.99% accuracy on average over the fourteen participants for various speeds (0.5 - 4m/s), slopes (-10 -20%), treadmill and overground terrain, loaded (13.6 kg) and unloaded, Exo On and Exo Off conditions, and different shoe types. Results from an evaluation outdoors overground on the energetics of eight subjects demonstrated a significant reduction for running when comparing Exo On to No Exo (3.9%) and for walking and running when comparing Exo On to Exo Off (12.2% and 8.2% respectively). This study represents the first demonstration of an autonomous wearable robot reducing the energy cost of running. Significant variation in response across subjects was observed, highlighting further improvements may be possible via assistance profile individualization with human-in-the-Ioop optimization.

Soft exosuits are a new approach for assisting with human locomotion, which applies assistive torques to the wearer through functional apparel. In this paper, we present a new version of autonomous multi-joint soft exosuit for gait assistance, particularly designed for overground walking. The soft exosuit assists with ankle plantarflexion, hip flexion, and hip extension, equally distributing the forces between ankle plantarflexion and hip flexion. A mobile actuation system was developed to generate high assistive forces, and Bowden cables are used to transmit the forces to the exosuit. A sensor harness connects two load cells and three IMU s per leg that are used to measure real-time data for a controller that commands desired force profiles as a function of the walking cycle. In addition, a control adaptation method was developed which adjusts control parameters while walking on irregular surfaces. In preliminary studies, the proposed method substantially improved the force consistency while walking over uneven terrain. Specifically, the number of steps where the peak force deviated from the target force decreased from 100 to 57 out of 250 steps, and RMS error on the peak force decreased from 90.0 N to 76.6 N with respect to 300 N target force. Also, a two-subject case study on country-course walking demonstrated the potential of this soft exosuit to improve human energy economy while walking overground.

This work presents the design, fabrication, calibration, and testing of a multi-touch force sensor designed to measure normal ground reaction forces generated by highspeed locomotion of milli-scale legged robots. The sensor is based on the optical principle of frustrated total internal reflection (FTIR) and is capable of resolving multiple simultaneous normal forces in the range of 50–1000 mN at a rate of 250 Hz with measurement error of less than 1%. The sensor is integrated with commercial, off-the-shelf motion capture hardware and the whole system is demonstrated with a simple experiment tracking a bouncing ball and simultaneously-recording kinematic state and ground reaction force data.