Reception of 4-level pulse amplitude modulation (PAM-4) requires a clock and data recovery (CDR) circuit, typically implemented by a PLL-like structure. An essential block in such a CDR is the phase detector which should detect whether the recovered clock leads or lags the incoming data edges. In typical implementations an incoming data edge is detected by sensing whether the incoming waveform crosses a data threshold level. However, there is some ambiguity in detecting the incoming data edge because PAM-4 modulation has 3 thresholds. If the waveform crosses multiple threshold levels, the level crossings will occur at different time instants due to the finite rise/fall time of the incoming waveform. In this work, we first analyze qualitatively and quantitatively CDR systems that use one threshold for phase adjustment. Here, eliminating the 2-level transitions decreases the amount of jitter injected by the phase detector. However, the available transitions for phase adjustment are also reduced, which lowers the CDR's robustness. Secondly, for CDR systems using three thresholds, a combination of two techniques: majority voting and elimination of 2-level transitions is investigated. We prove that in this case, the elimination of 2-level transitions is not needed and even gives a worse performance when implemented.

The article describes a numerical approach for Massive MIMO channel modeling that accounts for the effects of electromagnetic coupling between a user and the receiving device. The modeling is performed by a combination of the Finite-Difference Time-Domain and the Ray-Tracing methods, supplemented with a stochastic geometry model of the propagation environment. The influence of user-coupling on the channel properties was studied statistically using the singular value spread and matrix power ratio metrics of the channel correlation matrix. The time-averaged Poynting vector distribution in the near-field of the receiver was evaluated using a realistic human phantom model and the Maximum Ratio Transmission precoding scheme in the downlink. The average enhancement of the time-average Poynting vector magnitude at the receiver location, compared to the surrounding area, was found to be around 10 dB when using 36 antenna elements at the base station. The electromagnetic field exposure of the phantom was assessed in terms of the 10g-average peak-spatial Specific Absorption Rate and compared with the existing public guidelines. Comparison of the EMF and exposure results provides a new perspective on the future regulatory procedures.

In-band full-duplex (FD) wireless communication allows the simultaneous transmission and reception of data at the same frequency band, effectively doubling the spectral efficiency and data rate while reducing the latency. Previously published designs mostly target the self-interference (SI) cancellation in conventional wireless systems. In this paper, we focus on real-time SI cancellation for short-reach wireless FD systems. The superior signal quality of a point-to-point short-reach wireless system, allows the utilization of wideband communications to achieve a high throughput. Besides, in such wireless systems, the impacts of phase noise and nonlinear distortions are largely reduced, easing the SI cancellation. Moreover, the degradation of signal reception quality due to FD operation is experimentally evaluated in different environments. Experimental results of a prototype implementation show that a combination of antenna isolation and digital cancellation can already achieve an overall SI cancellation performance of 72.5 dB over a bandwidth of 123 MHz. This prototype can support a high-data-rate FD communication link of close to 1 Gbps up to 300 cm with an error vector magnitude lower than -26 dB in a typical indoor environment.

Energy consumption of customer premises equipment (CPE) has become a serious issue in the new generations of time-division multiplexing passive optical networks, which operate at 10 Gb/s or higher. It is becoming a major factor in global network energy consumption, and it poses problems during emergencies when CPE is battery-operated. In this paper, a low-energy passive optical network (PON) that uses a novel bit-interleaving downstream protocol is proposed. The details about the network architecture, protocol, and the key enabling implementation aspects, including dynamic traffic interleaving, rate-adaptive descrambling of decimated traffic, and the design and implementation of a downsampling clock and data recovery circuit, are described. The proposed concept is shown to reduce the energy consumption for protocol processing by a factor of 30. A detailed analysis of the energy consumption in the CPE shows that the interleaving protocol reduces the total energy consumption of the CPE significantly in comparison to the standard 10 Gb/s PON CPE. Experimental results obtained from measurements on the implemented CPE prototype confirm that the CPE consumes significantly less energy than the standard 10 Gb/s PON CPE.