Ambient backscatter (AB), making use of both energy harvesting and backscattering, has recently become a promising solution to communications among low-power devices and demonstrates its potential application in the Internet of Things. Existing AB systems adopt two-state amplitude shift keying or phase shift keying (PSK), where data are transmitted at the rate of one bit per symbol period. To increase the data rate, we investigate the high-order modulation where M -PSK is employed for backscattering. We derive the optimal multilevel energy detector and compute the closed-form symbol error rate. To show the realizability of the proposed design, we build a 4PSK-AB hardware prototype, in which the selection of load impedance is discussed with the aid of phasor diagram illustration. The hardware prototype can achieve the date rate of 20 kb/s. Besides, higher date rate is achievable for 98.7% of the time compared with binary AB communications, and the mean number of distinguishable symbols is 3.66.

We present Stork - an extension of the EPC C1G2 protocol allowing streaming of data to multiple Computational Radio Frequency IDentification tags (CRFIDs) simultaneously at up to 20 times faster than the prior state of the art. Stork introduces downstream attributes never before seen in (C)RFIDs: (i) fast feedback for CRFID downstream verification based on the internal EPC C1G2 memory check command - which we analytically and experimentally show to be the best possible downstream verification process based on EPC C1G2; (ii) ability to perform multi-CRFID transfer - which in our experiments speeds up downstream by more than two times compared to sequential transmission; and (iii) the use of compressed data streams - which improves firmware reprogramming times by up to 10% at large reader-to-CRFID distances.

Computational RFID (CRFID) devices are emerging platforms that can enable perennial computation and sensing by eliminating the need for batteries. Although much research has been devoted to improving upstream (CRFID to RFID reader) communication rates, the opposite direction has so far been neglected, presumably due to the difficulty of guaranteeing fast and error-free transfer amidst frequent power interruptions of CRFID. With growing interest in the market where CRFIDs are forever-embedded in many structures, it is necessary for this void to be filled. Therefore, we propose Wisent — a robust downstream communication protocol for CRFIDs that operates on top of the legacy UHF RFID communication protocol: EPC C1G2. The novelty of Wisent is its ability to adaptively change the frame length sent by the reader, based on the length throttling mechanism, to minimize the transfer times at varying channel conditions. We present an implementation of Wisent for the WISP 5 and an off-the-shelf RFID reader. Our experiments show that Wisent allows transfer up to 16 times faster than a baseline, non-adaptive shortest frame case, i.e. single word length, at sub-meter distance. As a case study, we show how Wisent enables wireless CRFID reprogramming, demonstrating the world's first wirelessly reprogrammable (software defined) CRFID.

In-band load modulation as a means of transferring information from a wirelessly-powered client device to a power provider in a wireless power transfer (WPT) system has long been considered to have an unacceptable impact on the efficiency of power transfer. Conventional load modulation involves either completely or severely detuning the receive coil in order to produce a detectable amplitude shift at the power provider side and thereby transfer information. In this work, we analyze the impact of load modulation on system efficiency by considering the power consumption of the transmit power amplifier (PA) and identify a tradeoff between communication capability and end-to-end wireless power transfer efficiency. We also determine how to select a load modulation strategy which reduces the degradation in power transfer efficiency while maintaining high-contrast uplink signaling. Finally, we explore the use of coherent demodulation (IQ demodulation) to reduce the mismatch requirement on a load modulation system by improving the power provider's sensitivity to load modulated signaling.

RF-powered computers are small devices that compute and communicate using only the power that they harvest from RF signals. While existing technologies have harvested power from ambient RF sources (e.g., TV broadcasts), they require a dedicated gateway (like an RFID reader) for Internet connectivity. We present Wi-Fi Backscatter, a novel communication system that bridges RF-powered devices with the Internet. Specifically, we show that it is possible to reuse existing Wi-Fi infrastructure to provide Internet connectivity to RF-powered devices. To show Wi-Fi Backscatter's feasibility, we build a hardware prototype and demonstrate the first communication link between an RF-powered device and commodity Wi-Fi devices. We use off-the-shelf Wi-Fi devices including Intel Wi-Fi cards, Linksys Routers, and our organization's Wi-Fi infrastructure, and achieve communication rates of up to 1 kbps and ranges of up to 2.1 meters. We believe that this new capability can pave the way for the rapid deployment and adoption of RF-powered devices and achieve ubiquitous connectivity via nearby mobile devices that are Wi-Fi enabled.

Communication primitives such as coding and multiple antenna processing have provided significant benefits for traditional wireless systems. Existing designs, however, consume significant power and computational resources, and hence cannot be run on low complexity, power constrained backscatter devices. This paper makes two main contributions: (1) we introduce the first multi-antenna cancellation design that operates on backscatter devices while retaining a small form factor and power footprint, (2) we introduce a novel coding mechanism that enables long range communication as well as concurrent transmissions and can be decoded on backscatter devices. We build hardware prototypes of the above designs that can be powered solely using harvested energy from TV and solar sources. The results show that our designs provide benefits for both RFID and ambient backscatter systems: they enable RFID tags to communicate directly with each other at distances of tens of meters and through multiple walls. They also increase the communication rate and range achieved by ambient backscatter systems by 100X and 40X respectively. We believe that this paper represents a substantial leap in the capabilities of backscatter communication.

Paper displays have a number of attractive properties, in particular the ability to present visual information perpetually with no power source. However, they are not digitally updatable or re-usable. Bistable display materials, such as e-paper, promise to enable displays with the best properties of both paper and electronic displays. However, rewriting a pixelated bistable display requires substantial energy, both for communication and for setting the pixel states.

We present the design of a communication system that enables two devices to communicate using ambient RF as the only source of power. Our approach leverages existing TV and cellular transmissions to eliminate the need for wires and batteries, thus enabling ubiquitous communication where devices can communicate among themselves at unprecedented scales and in locations that were previously inaccessible.