We use 3-D ray tracing to evaluate the performance of millimeter wave (mmWave) cellular in a realistic model of MetLife stadium, NJ, USA. We model thousands of human blockages using the dielectric properties at 28 GHz. Using this setup, we contrast the coverage and capacity performance with and without human blockages. Our study highlights that incorporating human models is essential for performance evaluation and also for deployment choice. We study the scaling in achievable data rates of three dense deployments in the stadium, and conclude that meeting the minimum 100 Mbps 5G requirement in stadiums can be challenging with a unicast mode of transmission. Broadcasting popular content in conjunction with a multiplexed unicast mode can provide minimum 100 Mbps rate for the broadcasted content.

We provide a comprehensive overview of mathematical models and analytical techniques for millimeter wave (mmWave) cellular systems. The two fundamental physical differences from conventional sub-6-GHz cellular systems are: 1) vulnerability to blocking and 2) the need for significant directionality at the transmitter and/or receiver, which is achieved through the use of large antenna arrays of small individual elements. We overview and compare models for both of these factors, and present a baseline analytical approach based on stochastic geometry that allows the computation of the statistical distributions of the downlink signal-to-interference-plus-noise ratio (SINR) and also the per link data rate, which depends on the SINR as well as the average load. There are many implications of the models and analysis: 1) mmWave systems are significantly more noise-limited than at sub-6 GHz for most parameter configurations; 2) initial access is much more difficult in mmWave; 3) self-backhauling is more viable than in sub-6-GHz systems, which makes ultra-dense deployments more viable, but this leads to increasingly interference-limited behavior; and 4) in sharp contrast to sub-6-GHz systems cellular operators can mutually benefit by sharing their spectrum licenses despite the uncontrolled interference that results from doing so. We conclude by outlining several important extensions of the baseline model, many of which are promising avenues for future research.

Initial deployments of millimeter wave (mm-wave) cellular networks are likely to be enabled with self-backhauling. In this paper, we propose a random spatial model to analyze uplink (UL) and downlink (DL) signal to interference plus noise ratio distribution and mean rates corresponding to different access-backhaul and UL-DL resource allocation schemes in a self-backhauled mm-wave cellular network with Poisson point process (PPP) deployment of users and base stations (BSs). In particular, we focus on heuristic implementations of static and dynamic time division duplexing (TDD) for access links with synchronized or unsynchronized access-backhaul (SAB or UAB) time splits. We propose PPP approximations to characterize the distribution of the new types of interference encountered with dynamic TDD and UAB. These schemes offer better resource utilization than static TDD and SAB, however, potentially higher interference makes their choice non-trivial and the offered gains sensitive to different network parameters, including UL/DL traffic asymmetry, user load per BS or number of slave BSs per master BS. One can harness notable gains from UAB and/or dynamic TDD only if backhaul links are designed to have much larger throughput than the access links.

In conventional applications of time division duplex (TDD) in cellular systems, the time resource split between uplink (UL) and downlink (DL) is fixed across all base stations (BSs) in the network. This leads to under utilization of BS resources when there is a mismatch between the expected and experienced UL/DL traffic in a given cell. A dynamic split that varies in each cell is desirable, but is challenging due to the high interference experienced by UL receivers in one cell from DL transmissions in adjacent cells. This paper analyzes the performance of UL users in dynamic TDD enabled next generation cellular networks using a stochastic geometry framework. The analysis highlights the trade-off between spectral efficiency and resource utilization for dynamic TDD. With appropriate interference mitigation, dynamic TDD offers a significant gain in data rates as compared to static TDD, which is higher when the BSs are lightly loaded and/or the fraction of UL users is low.

Large antenna arrays will be needed in future millimeter wave (mmWave) cellular networks, enabling a large number of different possible antenna architectures and multiple-input multiple-output (MIMO) techniques. It is still unclear which MIMO technique is most desirable as a function of different network parameters. This paper, therefore, compares the coverage and rate performance of hybrid beamforming enabled multiuser (MU) MIMO and single-user spatial multiplexing (SM) with single-user analog beamforming (SU-BF). A stochastic geometry model for coverage and rate analysis is proposed for MU-MIMO mmWave cellular networks, taking into account important mmWave-specific hardware constraints for hybrid analog/digital precoders and combiners, and a blockage-dependent channel model which is sparse in angular domain. The analytical results highlight the coverage, rate, and power consumption tradeoffs in multiuser mmWave networks. With perfect channel state information at the transmitter and round robin scheduling, MU-MIMO is usually a better choice than SM or SU-BF in mmWave cellular networks. This observation, however, neglects any overhead due to channel acquisition or computational complexity. Incorporating the impact of such overheads, our results can be re-interpreted so as to quantify the minimum allowable efficiency of MU-MIMO to provide higher rates than SM or SU-BF.

Millimeter wave (mmWave) links will offer high capacity but are poor at penetrating into or diffracting around solid objects. Thus, we consider a hybrid cellular network with traditional sub-6 GHz macrocells coexisting with denser mmWave small cells, where a mobile user can connect to either opportunistically. We develop a general analytical model to characterize and derive the uplink and downlink cell association in the view of the signal-to-interference-and-noise-ratio and rate coverage probabilities in such a mixed deployment. We offer extensive validation of these analytical results (which rely on several simplifying assumptions) with simulation results. Using the analytical results, different decoupled uplink and downlink cell association strategies are investigated and their superiority is shown compared with the traditional coupled approach. Finally, small cell biasing in mmWave is studied, and we show that unprecedented biasing values are desirable due to the wide bandwidth.

Millimeter wave (mmWave) cellular systems will require high-gain directional antennas and dense base station (BS) deployments to overcome a high near-field path loss and poor diffraction. As a desirable side effect, high-gain antennas offer interference isolation, providing an opportunity to incorporate self-backhauling, i.e., BSs backhauling among themselves in a mesh architecture without significant loss in the throughput, to enable the requisite large BS densities. The use of directional antennas and resource sharing between access and backhaul links leads to coverage and rate trends that significantly differ from conventional UHF cellular systems. In this paper, we propose a general and tractable mmWave cellular model capturing these key trends and characterize the associated rate distribution. The developed model and analysis are validated using actual building locations from dense urban settings and empirically derived path loss models. The analysis shows that, in sharp contrast to the interference-limited nature of UHF cellular networks, the spectral efficiency of mmWave networks (besides the total rate) also increases with the BS density, particularly at the cell edge. Increasing the system bandwidth does not significantly influence the cell edge rate, although it boosts the median and peak rates. With self-backhauling, different combinations of the wired backhaul fraction (i.e., the fraction of BSs with a wired connection) and the BS density are shown to guarantee the same median rate (QoS).

The use of dense millimeter wave (mmWave) cellular networks with highly directional beamforming stands as an intriguing solution to the current spectrum congestion problem. Due to significantly different propagation characteristics at such high frequencies, however, the coverage and rate trends differ drastically from conventional microwave networks. This paper aims to gain insights into the coverage and rate performance of mmWave cellular networks in major metropolitan cities. Our results confirm that, unlike conventional cellular networks, mmWave networks operating at 73 GHz carrier frequency are pre-dominantly noise-limited. Though larger system bandwidth leads to higher peak rates, it does not improve the cell edge rates. It is observed that dense base station (BS) deployment is the key to achieve both better coverage and rates in mmWave cellular networks. Further, based on actual building locations, we show the inadequacy of existing blockage models and validate a better blockage model.