Global allocations in the upper mid-band spectrum (4-24 GHz) necessitate a comprehensive exploration of the propagation behavior to meet the promise of coverage and capacity. This paper presents an extensive Urban Microcell (UMi) outdoor propagation measurement campaign at 6.75 GHz and 16.95 GHz conducted in Downtown Brooklyn, USA, using a 1 GHz bandwidth sliding correlation channel sounder over 40-880 m propagation distance, encompassing seven Line of Sight (LOS) and 13 Non-Line of Sight (NLOS) locations. Analysis of the path loss (PL) reveals lower directional and omnidirectional PL exponents compared to mmWave and sub-THz frequencies in the UMi environment, using the close-in (CI) free space PL (FSPL) model with a 1 m reference distance. Additionally, a decreasing trend in root mean square (RMS) delay spread (DS) and angular spread (AS) with increasing frequency was observed. The measured NLOS RMS DS and RMS AS mean values (as computed by 3GPP methods) are found to be consistently lower compared to 3GPP model predictions. Point-data tables with corresponding site-specific environmental information for all measured statistics at each TX-RX location are provided to support the models and results. The spatio-temporal statistics presented here offer valuable insights for the design of nextgeneration wireless systems and networks.

This paper presents sub-Terahertz (THz) channel characterization and modeling for an indoor industrial scenario based on radio propagation measurements at 142 GHz in four factories. We selected 82 transmitter-receiver (TX-RX) locations in both line-of-sight (LOS) and non-LOS (NLOS) conditions and collected over 75,000 spatial and temporal channel impulse responses. The TX-RX distance ranged from 5 to 87 m. Steerable directional horn antennas were employed at both ends and were switched between vertical and horizontal polarization. Measurements were conducted with the low RX and high RX to characterize the propagation channel for close-to-floor applications such as automated guided vehicles. Results show that the low RXs experience an average path loss increase of 10.7 dB and 6.0 dB at LOS and NLOS locations, respectively. In addition, channel enhancement measurements were conducted using a steerable large flat metal plate as a passive reflecting surface, demonstrating omnidirectional path loss reduction from 0.5 to 22 dB with a mean of 6.5 dB. This paper presents the first statistical channel characterization and path loss modeling at sub-THz frequencies, highlighting the potential for ultra-broadband factory communications in the 6G era.

Sub-Terahertz (THz) frequencies between 100 GHz and 300 GHz are being considered as a key enabler for the sixth-generation (6G) wireless communications due to the vast amounts of unused spectrum. The 3rd Generation Partnership Project (3GPP) included the indoor industrial environments as a scenario of interest since Release 15. This paper presents recent sub-THz channel measurements using directional horn antennas of 27 dBi gain at 142 GHz in a factory building, which hosts equipment manufacturing startups. Directional measurements with copolarized and cross-polarized antenna configurations were conducted over distances from 6 to 40 meters. Omnidirectional and directional path loss with two antenna polarization configurations produce the gross cross-polarization discrimination (XPD) with a mean of 27.7 dB, which suggests that dual-polarized antenna arrays can provide good multiplexing gain for sub-THz wireless systems. The measured power delay profile and power angular spectrum show the maximum root mean square (RMS) delay spread of 66.0 nanoseconds and the maximum RMS angular spread of 103.7 degrees using a 30 dB threshold, indicating the factory scenario is a rich-scattering environment due to a massive number of metal structures and objects. This work will facilitate emerging sub-THz applications such as super-resolution sensing and positioning for future smart factories.

Small-cell cellular base stations are going to be used for mmWave and sub-THz communication systems to provide multi-Gbps data rates and reliable coverage to mobile users. This paper analyzes the base station coverage of sub-THz communication systems and the system performance in terms of spectral efficiency through Monte Carlo simulations for both single-cell and multi-cell cases. The simulations are based on realistic channel models derived from outdoor field measurements at 142 GHz in urban microcell (UMi) environments conducted in downtown Brooklyn, New York. The single-cell base station can provide a downlink coverage area with a radius of 200 m and the 7-cell system can provide a downlink coverage area with a radius of 400 m at 142 GHz. Using a 1 GHz downlink bandwidth and 100 MHz uplink bandwidth, the 7-cell system can provide about 4.5 Gbps downlink average data rate and 410 Mbps uplink average data rate at 142 GHz.

Intelligent reflecting surfaces (IRS) have the potential to provide coverage extension and capacity improvement in many scenarios, particularly at millimeter wave (mmWave) and terahertz (THz) frequencies, by making the wireless channels controllable to mitigate blockages in propagation environments. In this paper, we present key propagation-related characteristics and optimal phase shift solutions of IRSs for different incident and reflection angles. Raytracing-based simulations of IRSs were performed at 28 GHz in both indoor and outdoor scenarios, and the results show that IRS can greatly extend coverage and improve capacity at low cost.

Terahertz frequency bands will likely be used for the next-generation wireless communication systems to provide data rates of hundreds of Gbps or even Tbps because of the wide swaths of unused and unexplored spectrum. This paper presents two outdoor wideband measurement campaigns in downtown Brooklyn (urban microcell environment) in the sub-THz band of 140 GHz with TX-RX separation distance up to 117.4 m: i) terrestrial urban microcell measurement campaign, and ii) rooftop surrogate satellite and backhaul measurement campaign. Outdoor omnidirectional and directional path loss models for both line-of-sight and non-line-of-sight scenarios, as well as foliage loss (signal attenuation through foliage), are provided at 140 GHz for urban microcell environments. These measurements and models provide an understanding of both the outdoor terrestrial (e.g., 6G cellular and backhaul) and non-terrestrial (e.g., satellite and unmanned aerial vehicle communications) wireless channels, and prove the feasibility of using THz frequency bands for outdoor fixed and mobile cellular communications. This paper can be used for future outdoor wireless system design at frequencies above 100 GHz.

High Altitude Platform Station (HAPS) has the potential to provide global wireless connectivity and data services such as high-speed wireless backhaul, industrial Internet of things (IoT), and public safety for large areas not served by terrestrial networks. A unified HAPS design is desired to support various use cases and a wide range of requirements. In this paper, we present two architecture designs of the HAPS system: i) repeater based HAPS, and ii) base station based HAPS, which are both viable technical solutions. The energy efficiency is analyzed and compared between the two architectures using consumption factor theory. The system performance of these two architectures is evaluated through Monte Carlo simulations and is characterized in metrics of spectral efficiency using LTE band 1 for both single-cell and multi-cell cases. Both designs can provide good downlink spectral efficiency and coverage, while the uplink coverage is significantly limited by UE transmit power and antenna gain. Using directional antennas at the UEs can improve the system performance for both downlink and uplink.

Millimeter-wave (mmWave) and sub-Terahertz (THz) frequencies are expected to play a vital role in 6G wireless systems and beyond due to the vast available bandwidth of many tens of GHz. This paper presents an indoor 3-D spatial statistical channel model for mmWave and sub-THz frequencies based on extensive radio propagation measurements at 28 and 140 GHz conducted in an indoor office environment from 2014 to 2020. Omnidirectional and directional path loss models and channel statistics such as the number of time clusters, cluster delays, and cluster powers were derived from over 15,000 measured power delay profiles. The resulting channel statistics show that the number of time clusters follows a Poisson distribution and the number of subpaths within each cluster follows a composite exponential distribution for both LOS and NLOS environments at 28 and 140 GHz. This paper proposes a unified indoor statistical channel model for mmWave and sub-Terahertz frequencies following the mathematical framework of the previous outdoor NYUSIM channel models. A corresponding indoor channel simulator is developed, which can recreate 3-D omnidirectional, directional, and multiple input multiple output (MIMO) channels for arbitrary mmWave and sub-THz carrier frequency up to 150 GHz, signal bandwidth, and antenna beamwidth. The presented statistical channel model and simulator will guide future air-interface, beamforming, and transceiver designs for 6G and beyond.

Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generation procedure are derived from empirical measurement data for 28 GHz and 140 GHz line-of-sight (LOS) and non-line-of-sight (NLOS) scenarios. The channel model is validated by showing that the simulated root mean square (RMS) delay spread and RMS angular spread yield good agreements with measured values. An indoor channel simulation software is built upon the popular NYUSIM outdoor channel simulator, which can generate realistic channel impulse response, PDP, and power angular spectrum.

Accurate channel modeling and simulation are indispensable for millimeter-wave wideband communication systems that employ electrically- steerable and narrow beam antenna arrays. Three important channel modeling components, spatial consistency, human blockage, and outdoor-to-indoor penetration loss, were proposed in the 3rd Generation Partnership Project Release 14 for mmWave communication system design. This paper presents NYUSIM 2.0, an improved channel simulator which can simulate spatially consistent channel realizations based on the existing drop-based channel simulator NYUSIM 1.6.1. A geometry-based approach using multiple reflection surfaces is proposed to generate spatially correlated and time-variant channel coefficients. Using results from 73 GHz pedestrian measurements for human blockage, a four-state Markov model has been implemented in NYUSIM to simulate dynamic human blockage shadowing loss. To model the excess path loss due to penetration into buildings, a parabolic model for outdoor-to-indoor penetration loss has been adopted from the 5G Channel Modeling special interest group and implemented in NYUSIM 2.0. This paper demonstrates how these new modeling capabilities reproduce realistic data when implemented in Monte Carlo fashion using NYUSIM 2.0, making it a valuable measurement-based channel simulator for fifth-generation and beyond mmWave communication system design and evaluation.

Accurate precise positioning at millimeter wave frequencies is possible due to the large available bandwidth that permits precise on-the-fly time of flight measurements using conventional air interface standards. In addition, narrow antenna beamwidths may be used to determine the angles of arrival and departure of the multipath components between the base station and mobile users. By combining accurate temporal and angular information of multipath components with a 3-D map of the environment (that may be built by each user or downloaded a-priori), robust localization is possible, even in non-line-of-sight environments. In this work, we develop an accurate 3-D ray tracer for an indoor office environment and demonstrate how the fusion of angle of departure and time of flight information in concert with a 3-D map of a typical large office environment provides a mean accuracy of 12.6 cm in line-of- sight and 16.3 cm in non-line-of-sight, over 100 receiver distances ranging from 1.5 m to 24.5 m using a single base station. We show how increasing the number of base stations improves the average non-line-of-sight position location accuracy to 5.5 cm at 21 locations with a maximum propagation distance of 24.5 m.

This paper provides indoor reflection, scattering, transmission, and large-scale path loss measurements and models, which describe the main propagation mechanisms at millimeter wave and Terahertz frequencies. Channel properties for common building materials (drywall and clear glass) are carefully studied at 28, 73, and 140 GHz using a wideband sliding correlation based channel sounder system with rotatable narrow-beam horn antennas. Reflection coefficient is shown to linearly increase as the incident angle increases, and lower reflection loss (e.g., stronger reflections) are observed as frequencies increase for a given incident angle. Although backscatter from drywall is present at 28, 73, and 140 GHz, smooth surfaces (like drywall) are shown to be modeled as a simple reflected surface, since the scattered power is 20 dB or more below the reflected power over the measured range of frequency and angles. Partition loss tends to increase with frequency, but the amount of loss is material dependent. Both clear glass and drywall are shown to induce a depolarizing effect, which becomes more prominent as frequency increases. Indoor propagation measurements and large-scale indoor path loss models at 140 GHz are provided, revealing similar path loss exponent and shadow fading as observed at 28 and 73 GHz. The measurements and models in this paper can be used for future wireless system design and other applications within buildings for frequencies above 100 GHz.

This paper provides an analysis of radio wave scattering for frequencies ranging from the microwave to the Terahertz band (e.g., 1 GHz–1 THz), by studying the scattering power reradiated from various types of materials with different surface roughnesses. First, fundamentals of scattering and reflection are developed and explained for use in wireless mobile radio, and the effect of scattering on the reflection coefficient for rough surfaces is investigated. Received power is derived using two popular scattering models — the directive scattering (DS) model and the radar cross section (RCS) model through simulations over a wide range of frequencies, materials, and orientations for the two models, and measurements confirm the accuracy of the DS model at 140 GHz. This paper shows that scattering can become a prominent propagation mechanism as frequencies extend to millimeter-wave (mmWave) and beyond, but at other times can be treated like simple reflection. Knowledge of scattering effects is critical for appropriate and realistic channel models, which further support the development of massive multiple input-multiple output (MIMO) techniques, localization, ray tracing tool design, and imaging for future 5G and 6G wireless systems.

With the relatively recent realization that millimeter wave frequencies are viable for mobile communications, extensive measurements and research have been conducted on frequencies from 0.5 to 100 GHz, and several global wireless standard bodies have proposed channel models for frequencies below 100 GHz. Presently, little is known about the radio channel above 100 GHz where there are much wider unused bandwidth slots available. This paper summarizes wireless communication research and activities above 100 GHz, overviews the results of previously published propagation measurements at D-band (110-170 GHz), provides the design of a 140 GHz wideband channel sounder system, and proposes indoor wideband propagation measurements and penetration measurements for common materials at 140 GHz which were not previously investigated.

This article presents measurement guidelines and verification procedures for antenna cross-polarization discrimination (XPD) and penetration loss measurements for millimeter wave (mmWave) channel sounder systems. These techniques are needed to ensure accurate and consistent measurements by different researchers at different frequencies and bandwidths. Measurements at 73 GHz are used to demonstrate and verify the guidelines, and show the consistency of the antenna XPD factor and the penetration loss at different transmitter-receiver (T-R) separation distances, thus providing a systematic method that may be used at any frequency for reliable field measurements.