Multi-user MIMO (MU-MIMO) is a technique that improves spectral efficiency by allowing concurrent communication between one access point (AP) and multiple clients. In practice, the expected gain is not always achieved and is sometimes even negative. We experimentally demonstrate that the downlink MU-MIMO performance in a practical network not only depends on the client's channel but is also influenced by factors that are not captured by conventional models, such as client motion and device type. We propose a data-driven algorithm with a low computational complexity that determines whether a client should operate in MU mode and the MU-MIMO group for clients in MU mode. Such a mode and group selection algorithm is based on a sequence of channel state information (CSI), SNR, and client device type. The algorithm can automatically adapt to the motion and characteristics of individual clients. Experimental results using implementation on a commodity 802.11ac AP show that the proposed data-driven mode and group selection algorithm can improve network throughput by up to 35% over existing algorithms based on conventional models. We also show that the proposed data-driven algorithm has limited sensitivity to environmental changes and can be deployed into new environments without retraining.

The Wave Controlled Aliasing In Parallel Imaging (Wave-CAIPI) technique manifests great potential to highly accelerate three-dimensional (3D) balanced steady-state free precession (bSSFP) through substantially reducing the geometric factor (g-factor) and aliasing artifacts of image reconstruction. However, severe banding artifacts appear in bSSFP imaging due to unbalanced gradients with nonzero 0thmoment applied by the conventional Wave-CAIPI technique. In this study, we propose a 3D Wave-bSSFP scheme that adopts truncated wave gradients with zero 0thmoment to avoid introducing additional banding artifacts and to maintain the advantages of wave encoding. The simulation results indicate that the number of wave cycles that are truncated and different options of applying wave gradients affect both the g-factor reduction and image quality, but the influence is limited. In phantom experiments, the proposed technique shows similar acceleration performance as the conventional Wave-CAIPI technique and effectively eliminates its introduced banding artifacts. Additionally, Wave-bSSFP obtains up to $12\times $ retrospective acceleration at 0.8 mm isotropic resolution in in vivo 3D brain experiments and is superior to the state-of-the-art Controlled Aliasing In Parallel Imaging Results IN Higher Acceleration (CAIPIRINHA) technique, according to both visual validation and quantitative analysis. Moreover, in vivo 3D spine and abdomen imaging demonstrate the potential clinical applications of Wave-bSSFP with fast acquisition speed, improved isotropic resolution and fine image quality.

Multi-User Multiple-Input and Multiple-Output (MU-MIMO) is a technique that allows concurrent transmissions between one access point (AP) and multiple clients to improve spectral efficiency. In practice, however, the MU-MIMO is sensitive to client mobility and is sometimes even harmful to the performance in networks with moving clients. In this paper, we identify that it is essential to optimize the MU-MIMO performance with moving clients by jointly selecting the sounding period, the number of spatial streams, and client grouping with the consideration of the client density of the network. We develop a data-driven model that estimates client throughput with the consideration of these parameters, as well as an algorithm that jointly determines the parameters for each client with low computational complexity. Using a commodity 802.11ax network, we experimentally demonstrate the significant impact of the key factors on MU-MIMO performance. Based on experimental data, we develop an emulation model to evaluate network performance with different client densities and mobility. Emulation results show that our proposed algorithm outperforms conventional schemes by over 20% in MU-MIMO networks with moving clients.

Multi-user MIMO (MU-MIMO) is a technique in 802.11ac and 802.11ax that improves spectral efficiency by allowing concurrent communication between one AP and multiple clients. In practice, the expected gain is not always achieved and is sometimes even negative. Using a commodity 802.11ac AP, we experimentally determine that the inclusion of clients either in motion or with low SNR can cause throughput below that of single-user transmissions. We then propose a pre-screening algorithm using reinforcement learning to predict if a client can benefit from participating in MU-MIMO. Our algorithm is based on a sequence of channel state information (CSI), SNR, and client device type, and can automatically adapt to the motion of individual clients. Experimental results using a commodity AP show that the additional implementation of the pre-screening algorithm alone, without otherwise modifying MU-MIMO client grouping or link parameter selection algorithms, can improve system throughput by up to 40% when half of the clients are moving. Over 20% throughput improvement is maintained when between 25% to 75% of the clients are moving.

Due to a lack of fetal imaging coils, the standard commercial abdominal coil is often used for fetal imaging, the performance of which is limited by its insufficient coverage, element number, and Signal-to-noise ratio (SNR). In this paper, a dedicated 36-channel coil array, of which size can best fit the body sizes of pregnancy gestation from 20 to 37+ weeks, was designed for fetal imaging at 3T. SNR with full phase encoding and G-factor denoted as noise amplification for parallel imaging were quantitatively evaluated by phantom studies. Compared with a commercial abdominal coil array, the proposed 36-channel fetal array provides not only SNR improvements in full phase encoding (with 10% in the region where the whole fetal body was located, and up to 40% in the edge region where the fetal brain and heart may appear) but also an augmented parallel imaging capability and remarkable SNR improvements at high acceleration factors.

Continuous deployment is the practice of releasing software updates to production as soon as it is ready, which is receiving increased adoption in industry. The frequency of updates of mobile software has traditionally lagged the state of practice for cloud-based services for a number of reasons. Mobile versions can only be released periodically. Users can choose when and if to upgrade, which means that several different releases coexist in production. There are hundreds of Android hardware variants, which increases the risk of having errors in the software being deployed.