Due to the continuous demand for higher bit rates, the management of the spatio-temporal intersymbol interference in frequency-selective multiple-input multiple-output (MIMO) channels becomes increasingly important. For single-input single-output channels, equalized precoded partial-response signaling is capable of handling a large amount of intersymbol interference, but, to date, no equalization scheme with general partial-response signaling has been presented for the frequency-selective MIMO channel. Not only does this contribution extend partial-response signaling to the MIMO channel by proposing a general spatio-temporal partial-response precoder, but it also develops a minimum mean-squared-error optimization framework in which the equalization coefficients and the spatio-temporal target response are jointly optimized. Three iterative optimization algorithms are discussed, which update (part of) a row of the target impulse response matrix in each iteration. In particular, the third algorithm reformulates this row optimization as a lattice decoding problem. Numerical simulations confirm that the general partial-response signaling clearly outperforms the traditional full-response signaling in terms of the mean squared error and the bit error rate. The third optimization algorithm has a better performance but a higher complexity, compared to the first and the second algorithm.

Partial-response signaling is known to facilitate the equalizer design because a controlled amount of residual interference is permitted. The design of the target impulse response of the partial-response precoder often assumes perfect channel state information, which is unfortunately not available at the transmitter in most practical applications. Consequently, this contribution focuses instead on the robust and joint design of a spatio-temporal target impulse response and the equalization coefficients for a frequency-selective fading multiple-input multiple-output communication channel based on current and/or previous noisy channel estimates. More precisely, the error in the channel estimates is statistically modeled, and robustness is achieved by minimizing the mean-squared estimation error averaged over the joint distribution of the actual channel and the available channel estimates. Numerical results of the bit error rate confirm that the proposed robust partial-response signaling not only provides a significant performance gain compared to traditional full-response signaling, but also outperforms the naive approach, which ignores channel estimation errors.

High-speed communication over mutually coupled channels can be severely affected by intersymbol interference (ISI) and crosstalk (XT). Multiple-input multiple-output (MIMO) equalization is known to mitigate both ISI and XT, but requires accurate channel information at the receiver (RX) and/or transmitter (TX), when the channel is stochastic. However, since adjusting the equalization filters to the specific channel realization involves a considerable implementational and computational complexity, it is desirable to keep the equalization filters fixed irrespective of the specific channel realization, especially when the channel variability is relatively small. Therefore, we propose a general MIMO transceiver scheme where the equalization filters depend on the channel statistics rather than the actual channel. More specifically, by considering the time-domain equalization with the fixed linear MIMO pre-equalization and adjustable MIMO decision feedback equalization, the complexity associated with passing channel information from the RX to the TX is avoided, and the computationally intensive and iterative calculations of the fixed pre-equalizer can be performed offline rather than on-chip. The proposed equalization scheme is shown to yield only a small performance degradation compared to fully adjustable equalization schemes, thereby enabling multi-Gbit/s chip-to-chip communication over low-cost electrical interconnects which are prone to manufacturing tolerances.

While the requirements for delivering high throughputs increase exponentially with every generation of access node hardware, the device cost is of primary concern. As a result, multiple- input multiple-output (MIMO) equalization, which has been shown to facilitate multi-Gbit/s communication over low-cost parallel electrical interconnects, is emerging as an attractive high- speed interconnect solution for next-generation access nodes. Because of the high operating frequencies, however, the transfer functions of the on- and off-chip interconnects become highly susceptible to manufacturing tolerances (MTs); hence, the equalization filters must be adjusted to the specific channel realization to achieve optimal performance, which involves a high implementation and computational complexity. Considering that the MTs are usually limited, we propose a robust low-complexity transceiver consisting of a fixed MIMO linear pre-equalizer (which avoids the need for feeding back the channel state information to the transmitter), with either a fixed or adjustable MIMO decision- feedback equalizer (DFE). For a specific chip-to- chip interconnect operating at 75 Gbit/s per line and a 26 dB signal-to-noise ratio, we show that the resulting bit error rate does not exceed 10^(-12) for MTs up to 10.5% (fixed DFE) and 17.7% (adjustable DFE) of the nominal line width.