Maintaining balance during gait in the mediolateral direction requires more active motor control than in the anteroposterior direction. Step width modulation is a key strategy used by healthy individuals to achieve mediolateral walking balance, but it can be disrupted in populations with poor sensorimotor integration and weak hip abductors, such as the elderly, stroke patients, and people with lower limb amputation. Wearable hip exoskeletons have the potential to serve as assistive or rehabilitation devices for these populations, but there has been limited research on their appropriate usage. In this study, we successfully demonstrated the feasibility of controlling step width using a mediolaterally acting robotic hip exoskeleton. We were able to effectively adjust the user's step width by increasing or decreasing it to predefined targets through the regulation of admittance control parameters governing the device. The maximum average error to increase or decrease the step width was 1.2 cm. This research has the potential to facilitate the development of assistive and rehabilitation applications focused on enhancing the mediolateral gait balance of individuals with neurological impairments, elderly individuals, and amputees via the control of step width.

Robotic prosthetic legs have the potential to significantly improve the quality of life for lower limb amputees to perform locomotion in various environments and task conditions. However, these devices lack the capability to recover from internal intrinsic control faults, which can lead to harmful consequences affecting the user's gait performance and eroding trust in these robotic devices. Therefore, a reliable fault detection system is necessary to detect intrinsic faults in a timely manner and provide a compensatory response to mitigate their effects. This paper focuses on designing an active fault detector for a robotic knee prosthesis and demonstrates its effectiveness in real time. The developed system utilizes a Gaussian Process model to estimate knee angular velocity, which is sensitive to intrinsic faults and relies on the difference between estimated velocity and the actual measurement to detect internal control faults. In an offline analysis, the developed detector demonstrated a higher detection rate, lower false alarm ratio, and faster detection time compared with the two approaches reported previously. An online demonstration was also conducted with a unilateral amputee participant and showed performance similar to that of offline analysis. We expect that this detector can be integrated into a fault tolerance strategy to enhance the reliability and safety of robotic prosthetic legs, enabling users to perform their everyday tasks with greater confidence.

Existing robotic lower-limb prostheses use autonomous control to address cyclic, locomotive tasks, but are inadequate in adapting to variations in non-cyclic and unpredictable tasks. This study aims to address this challenge by designing a novel electromyography (EMG)-driven musculoskeletal model for volitional control of a robotic ankle-foot prosthesis. The proposed controller ensures continuous control of the device, allowing users to freely manipulate the prosthesis behavior. A Hill-type muscle model was implemented to model a dorsiflexor and a plantarflexor to function around a virtual ankle joint. The model parameters for a subject specific model was determined by fitting the model to the experimental data collected from an able-bodied subject. EMG signals recorded from antagonist muscle pairs were used to activate the virtual muscle models. This model-based approach was then validated via offline simulations and real-time prosthesis control. Additionally, the feasibility of the proposed prosthesis control on assisting the user's functional tasks was demonstrated. The present control may further improve the function of robotic prosthesis for supporting versatile activities in individuals with lower-limb amputations.

Robotic exoskeletons are exciting technologies for augmenting human mobility. However, designing such a device for seamless integration with the human user and to assist human movement still is a major challenge. This paper aims at developing a novel data-driven solution framework based on reinforcement learning (RL), without first modeling the human-robot dynamics, to provide optimal and adaptive personalized torque assistance for reducing human efforts during walking. Our automatic personalization solution framework includes the assistive torque profile with two control timing parameters (peak and offset timings), the least square policy iteration (LSPI) for learning the parameter tuning policy, and a cost function based on a transferred work ratio. The proposed controller was successfully validated on a healthy human subject to assist unilateral hip extension in walking. The results showed that the optimal and adaptive RL controller as a new approach was feasible for tuning assistive torque profile of the hip exoskeleton that coordinated with human actions and reduced activation level of hip extensor muscle in human.

The tuning process for a robotic prosthesis is a challenging and time-consuming task both for users and clinicians. An automatic tuning approach using reinforcement learning (RL) has been developed for a knee prosthesis to address the challenges of manual tuning methods. The algorithm tunes the optimal control parameters based on the provided knee joint profile that the prosthesis is expected to replicate during gait safely. This paper presents an intuitive interface designed for the prosthesis users and clinicians to choose the preferred knee joint profile during gait and use the autotuner to replicate in the prosthesis. The interface-based approach is validated by observing the ability of the tuning algorithm to successfully converge to various alternate knee profiles by testing on two able-bodied subjects walking with a robotic knee prosthesis. The algorithm was found to converge successfully in an average duration of 1.15 min for the first subject and 2.31 min for the second subject. Further, the subjects displayed different preferences for optimal profiles reinforcing the need to tune alternate profiles. The implications of the results in the tuning of robotic prosthetic devices are discussed.

Ankle joints play key roles in everyday locomotion, such as walking, stair climbing, and sit-to-stand. Despite the achievement in designing powered prosthetic ankles, engineers still face challenges to duplicate the full mechanics of ankle joints, including high torque, large range of motion (ROM), low profile, backdrivability, and efficiency, using electric motors and related transmissions. In this study, our goal was to develop a new active prosthetic ankle, Variable Spring embedded Motor-ball screw (VSeM) ankle, to meet all these requirements at the same time. Using a manually adjustable elastic element, which is parallel with our motor actuator, we can readjust the ROM of VSeM to handle all normal locomotion tasks. VSeM’s capability to mimic human ankle was validated through both bench tests and human subject tests.

Powered knee prostheses, compared to traditional energetically-passive knee prostheses, greatly enhance the mobility of transfemoral amputees. However, powered prostheses have a large number of control parameters that must be adjusted for individual amputee users, which presents a great challenge for clinical use. To address this challenge, we proposed and compared 2 automatic tuning strategies (i.e. parallel and sequential) using our newly developed optimal adaptive dynamic programming (ADP) tuner that objectively tuned the control parameters of an experimental powered knee prosthesis to mimic the knee profile of an able-bodied person (i.e. reference profile). With the parallel tuning strategy, we tuned all control parameters during the stance and the swing phases simultaneously. With the sequential tuning strategy, we alternately tuned stance or swing phase control parameters while fixing the remaining parameters. One able-bodied subject with a prosthesis adapter and one transfemoral amputee subject walked with the experimental powered knee prosthesis under both tuning strategies. Results show that with both tuning strategies, the ADP tuner successfully tuned the impedance parameters to match the prosthetic knee profile to the reference profile. Additionally, the parallel strategy outperformed the sequential strategy with better convergence to the reference profile. Interestingly, with the sequential tuning strategy, tuning during the swing phase greatly impacted the subsequent stance phase profile, but the impact was not as great when the order of tuning was switched. The ability to simultaneously adjust all control parameters with ADP using a parallel strategy may be a preferred solution for the current high-dimension control challenge, which may lead to more advanced, adaptive powered knee prostheses.