Radio frequency (RF) wireless power transfer (WPT) is an appealing technology to provide sustainable and cost-efficent power supply to low-power devices in future wireless systems. However, the inherently low end-to-end power transfer efficiency (PTE) is a serious challenge for practical applications. The key contributing factors include channel losses, transceivers’ power consumption, and losses from components such as the digital-to-analog converter (DAC), high-power amplifier (HPA), and rectenna. Careful consideration of these factors is essential for optimizing PTE, which is the focus of this research. Herein, we consider a fully connected hybrid multi-antenna transmit architecture that aims to charge non-linear energy harvesters. First, we present a mathematical framework to determine the harvested power from multi-tone signal transmissions and the system’s power consumption. Then, we formulate a joint waveform and analog beamforming design problem to minimize system’s power consumption and fulfill user’s charging needs. With this in place, and due to the problem high-complexity, we propose a particle swarm optimization (PSO)-based solution. Moreover, we also model the problem as a Markov decision process and propose a solution based on deep deterministic policy gradient (DDPG). Numerical results demonstrate that the proposed algorithms converge to suboptimal solutions. Moreover, simulation results show that system power consumption reduces with lower DAC and phase shifter resolution, as well as increased antenna length. Conversely, power consumption rises with the number of users and RF chains. Notably, across all these scenarios, PSO-JWB outperforms DDPG-JWB, requiring lower overall system power consumption.

This paper investigates the problem of energy beamforming for wireless power transfer (WPT) using dynamic metasurface antennas (DMAs).We propose a novel solution based on the bat algorithm (BA) to efficiently optimize the beamforming process. The proposed BA-based scheme enables simultaneous charging of multiple devices while avoiding power transmission in specific directions, such as areas where people or animals may be present. Our approach provides a robust and computationally efficient solution, considering key system constraints, including power transfer efficiency, antenna configurations, and DMA characteristics. Simulation results demonstrate that the BA-based method outperforms existing techniques in the literature, particularly those relying on alternating optimization, by achieving lower total power consumption and reduced computational complexity. These findings highlight the potential of the proposed method as a promising solution for future WPT systems employing DMAs.

Radio frequency (RF) wireless power transfer (WPT) is a promising technology to seamlessly charge low-power devices, but its low end-to-end power transfer efficiency remains a critical challenge. To address the latter, low-cost transmit/radiating architectures, e.g., based on reconfigurable intelligent surfaces (RISs), have shown great potential. Beyond diagonal (BD) RIS is a novel branch of RIS offering enhanced performance over traditional diagonal RIS (D-RIS) in wireless communications, but its potential gains in RF-WPT remain unexplored. Motivated by this, we analyze a BD-RIS-assisted single-antenna RF-WPT system to charge a single rectifier, and formulate a joint beamforming and multi-carrier waveform optimization problem aiming to maximize the harvested power. We propose two solutions relying on semi-definite programming for fully connected BD-RIS, a successive convex approximation (SCA)-based beamforming approach, and an efficient low-complexity iterative method relying on SCA. Numerical results show that the proposed algorithms converge and that adding transmit sub-carriers or RIS elements improves the harvesting performance. We show that the transmit power budget impacts the relative power allocation among different sub-carriers depending on the rectifier’s operating regime, while BD-RIS shapes the cascade channel differently for frequency-selective and flat scenarios. Finally, we verify by simulation that BD-RIS and D-RIS achieve the same performance under pure far-field line-of-sight conditions (in the absence of mutual coupling). Meanwhile, BD-RIS outperforms D-RIS as the non-line-of-sight components of the channel become dominant.

Radio frequency (RF) wireless power transfer (WPT) is promising for promoting sustainability in future wireless systems, but its low end-to-end power transfer efficiency is a critical challenge. For this, reconfigurable intelligent surfaces (RISs) can be leveraged to enhance efficiency by providing nearly passive beamforming gains. Beyond diagonal (BD) RIS is a new RIS variant offering greater performance benefits than traditional diagonal RIS (D-RIS), though its potential for RF-WPT remains unexplored. Motivated by this, we consider a single-input single-output BD-RIS-aided RF-WPT system and we formulate a joint beamforming and waveform optimization problem aiming to maximize the harvested power at the receiver. We propose an optimization framework relying on successive convex approximation, alternating optimization, and semi-definite relaxation. Numerical results show that increasing the number of transmit sub-carriers or RIS elements improves the harvested power. We verify by simulation that BD-RIS leads to the same performance as D-RIS under far-field line-of-sight conditions (in the absence of mutual coupling), while it outper-forms D-RIS as the non-line-of-sight components dominate.

Radio frequency (RF) wireless power transfer (WPT) is a promising technology for future wireless systems. However, the low power transfer efficiency (PTE) is a critical challenge for practical implementations. One of the main inefficiency sources is the power consumption and loss introduced by key components such as high-power amplifier (HPA) and rectenna, thus they must be carefully considered for PTE optimization. Herein, we consider a near-field RF-WPT system with a dynamic metasurface antenna (DMA) at the transmitter and non-linear energy harvesters. We provide a mathematical framework to calculate the power consumption and harvested power from multi-tone signal transmissions. Based on this, we propose an approach relying on alternating optimization and successive convex approximation for waveform optimization and beam focusing to minimize power consumption while meeting energy harvesting requirements. Numerical results show that increasing the number of transmit tones reduces the power consumption by leveraging the rectifier’s non-linearity more efficiently. Moreover, they demonstrate that increasing the antenna length improves the performance, while DMA outperforms fully-digital architecture in terms of power consumption. Finally, our results verify that the transmitter focuses the energy on receivers located in the near-field, while energy beams are formed in the receivers’ direction in the far-field region.

Radio frequency (RF) wireless power transfer (WPT) is a promising technology for sustainable support of massive Internet of Things (IoT). However, RF-WPT systems are characterized by low efficiency due to channel attenuation, which can be mitigated by precoders that adjust the transmission directivity. This work considers a multi-antenna RF-WPT system with multiple non-linear energy harvesting (EH) nodes with energy demands changing over discrete time slots. This leads to the charging scheduling problem, which involves choosing the precoders at each slot to minimize the total energy consumption and meet the EH requirements. We model the problem as a Markov decision process and propose a solution relying on a low-complexity beamforming and deep deterministic policy gradient (DDPG). The results show that the proposed beamforming achieves near-optimal performance with low computational complexity, and the DDPG-based approach converges with the number of episodes and reduces the system’s power consumption, while the outage probability and the power consumption increase with the number of devices.

One of the primary goals of future wireless systems is to foster sustainability, for which, radio frequency (RF) wireless power transfer (WPT) is considered a key technology enabler. The key challenge of RF-WPT systems is the extremely low end-to-end efficiency, mainly due to the losses introduced by the wireless channel. Distributed antenna systems are undoubtedly appealing as they can significantly shorten the charging distances, thus, reducing channel losses. Interestingly, radio stripe systems provide a cost-efficient and scalable way to deploy a distributed multi-antenna system, and thus have received a lot of attention recently. Herein, we consider an RF-WPT system with a transmit radio stripe network to charge multiple indoor energy hotspots, i.e., spatial regions where the energy harvesting devices are expected to be located, including near-field locations. We formulate the optimal radio stripe deployment problem aimed to maximize the minimum power received by the users and explore two specific predefined shapes, namely the straight line and polygon-shaped configurations. Then, we provide efficient solutions relying on geometric programming to optimize the location of the radio stripe elements. The results demonstrate that the proposed radio stripe deployments outperform a central fully-digital square array with the same number of elements and utilizing larger radio stripe lengths can enhance the performance, while increasing the system frequency may degrade it.