This paper presents the MOTORE++ system, a Portable, mobile haptic interface with the unique feature of using its wheels to deploy rehabilitation exercises to users. MOTORE++ is a battery powered device, with hot swap batteries, capable to run autonomously for almost an hour. MOTORS++ is a technology shift enhancement improvement over the previous version. Its new electronic architecture allows several communication protocols (RS232, WiFi, Bluetooth) that provide link stability in all running scenarios. The device also implements a cutting edge computing architecture and a novel position sensor jointly developed with Anoto®to deliver precise sensor fusion and stability to the localization and force generation algorithms. In the present papers we will describe the relevant new features of the device, and we will review the major innovation with respect to the existing mobile haptic interfaces.

The present paper introduces a novel type of haptic interface which is fully portable and employs only onboard sensors and electronics to solve accurate localization and force feedback generation. The device offers 2DOF force control while sliding on a plane and maintaining its orientation comfortable for the user. The device generates force feedback information without any intermediate link between the motion wheels and the grasping handle. The device has been designed for application in neuro-rehabilitation protocols and it adopts specific mechanical, electrical and control solutions in order to cope with patient requirements. The paper describes the mechanical and electronic solutions as well as the most relevant features of control implementation issues that were addressed in the system design.

The paper presents a controller for a multi-fingered underactuated prosthetic hand based on tendon transmission. The control architecture is implemented in two subsequent and different phases. The first one is the pre-shaping of the hand, based on the grasp type is implemented by stand-alone motion controllers using PID position control algorithms. The desired force closure value is calculated according to the pre-shape measured tendons tension and to the grasping force. In the second phase, the involved fingers rapidly close around the object to perform a balanced distribution of the forces within the hand, as it happens in the human hand. The controller is thus able to perform successfully many stable grasps. An overview of the hardware architecture and the results in terms of grasping capabilities based on Cutkosky grasp taxonomy are also presented

This paper presents recent results aimed at developing a functional prosthetic hand characterized by an EMG-control and by a simple and low cost fabrication technology. In order to overcome some limitations of current prosthetic hands mainly related to the poor functionality and controllability, the prosthetic hand has been designed following a biomechatronic approach based on biologically-inspired design solutions. The core of the project described in this paper is the fabrication of a compliant under-actuated prosthetic hand: the structure of the hand (both palm and fingers) is moulded as a soft polymeric single part with compliant joints and embedded tendon driven underactuated mechanism for providing adaptive grasp. In order to make user trials, the hand is equipped with simple but functional EMG-based control of the single motor incorporated in the hand, and is integrated with a prosthesis socket. The paper presents the biomechatronics design, the fabrication process, the integration of the prosthetic device and first experimental results.

In this paper, some recent results about the experimental trials we are performing on a functional prosthetic hand characterized by an EMG-control and by a simple and low cost fabrication technology are shown. The innovation described in this paper is the fabrication of a compliant under-actuated prosthetic hand. The structure of the hand (both palm and fingers) is moulded as a soft polymeric single part with compliant joints and embedded tendon driven under-actuated mechanism for providing adaptive grasp. The prosthetic hand has been designed following a biomechatronic approach based on biologically-inspired design solutions. We describe the second release of this prosthesis. The evaluating tests are related to the maximum force exerted during grasping and to the fatigue problems occurring with cables and joint.

Among social infrastructure technologies, robot technology (RT) is expected to play an important role in solving the problems of both decrease of birth rate and increase of elderly people in the 21st century, specially but not only in Japan. In order to achieve this objective, the new generation of personal robots should be capable of a natural communication with humans by expressing human-like emotion. In this sense, human hands play a fundamental role in communication, because they have grasping, sensing and emotional expression ability. This paper presents the recent results of the collaboration between the Takanishi Lab of Waseda University, Tokyo, Japan, and the Arts Lab of Scuola Superiore Sant'Anna, Pisa, Italy, and ROBOCASA. In this paper, the development of a novel anthropomorphic hand for humanoid robotics RCH-1 (ROBOCASA Hand No.1) and its integration into a humanoid robotic platform, named WE-4RII (Waseda Eye No.4 Refined II) is presented.

This paper presents an underactuated artificial hand intended for functional replacement of the natural hand in upper limb amputees. The natural hand has three basic functionalities: grasping, manipulation and exploration. To accomplish the goal of restoring these capabilities by implanting an artificial hand, two fundamental steps are necessary: to develop an artificial hand equipped with artificial proprioceptive and exteroceptive sensors and to fabricate an appropriate interface able to exchange sensory-motor signals with the amputee's body and the central nervous system. In order to address these objectives, we have studied an underactuated hand according to a biomimetic approach, and we have exploited robotic and microengineering technologies to design and fabricate its building blocks. The architecture of the hand comprises the following modules: an actuator system embedded in the underactuated mechanical structure (artificial musculoskeletal system), a proprioceptive sensory system (position and force sensors), an exteroceptive sensory system (3D force sensors distributed on the cosmetic glove), an embedded control unit, and a human/machine interface. The first prototype of the artificial hand has been designed and fabricated. The hand is underactuated, and is equipped with opposable thumb and a proprioceptive sensory system. This paper presents the fabrication and experimental characterization of the hand, focusing on the mechanical structure, the actuator system and the proprioceptive sensory system.